Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
d e. Time and date Displays current time and date. e 1 Finding new stations - DAB As time passes new stations may become available. To find new stations proceed as follows: 1. Press and release the AutoTune button, the display will show "Autotune Quick Scan". Your radio will perform a scan of the UK DAB frequencies. As new stations are found the station counter on the right-hand side of the display will increase and stations will be added to the list 2. To carry out a full scan of the entire DAB Band III frequencies press and hold down the AutoTune button for more than 2 seconds and then release. The display will show "Autotune Full scan". As new stations are found the station counter on the right-hand side of the display will increase and stations will be added to the list 1 2 Autoselect - DAB As an alternative to pressing the tuning control to select a station your radio can be set so as to automatically select a station. 1. Press either the Tuning up or down buttons a few times, immediately press and hold in the Select button until the display shows "Autoselect ON". 2. Scroll through the tuning list using the Tuning up or down buttons until the station you require is visible on the display, after a few seconds your radio will automatically select the station shown on the display. 3. To switch off Autoselect press either the Tuning up or down buttons a few times, immediately press and hold in the Select button until the display shows "Autoselect OFF". 1 2 If you need any further advice, please call our Technical Helpline on :020 8758 0338 (Mon-Fri) Manual Tuning - DAB Manual tuning allows you to tune directly to the various DAB Band III channels. UK DAB stations located in the range 11B to 12D. 1. Press and hold in the Select button until the display shows "Manual tune". 2. Press the Tuning up or down buttons to find the required DAB channel. 3. Press and release the Select button to select the channel. 4. Press the Tuning up or down buttons to select the stations contained within the Multiplex for the selected DAB channel. 1 2 5. Press and release the Select button to return to normal tuning mode. Signal strength display - DAB 1. Repeatedly press and release the Info button until the lower line of the display shows signal strength. 2. Position your radio and angle the telescopic aerial for best reception using the signal strength display as a guide. Move your radio around and position so as to give maximum number of black rectangles on signal strength display. 3. The clear unfilled rectangle indicates minimum signal level required for satisfactory reception. 1 Operating your radio - FM 1. Fully extend the telescopic aerial. 2. Press the StandBy button to switch on your radio. The display will show "Roberts DAB digital radio" for a few seconds. 3. Press the Band button to select the FM band. 4. Press and immediately release the Auto Tune button, your radio will scan in an upwards direction (low frequency to high frequency) and stop automatically when it finds a station of sufficient strength. 5. After a few seconds the display will update and show station name. 1 2 3 6. To find other stations press and release the AutoTune button as before. 7. To scan the FM band in a downwards direction (high frequency to low frequency) press and hold down the AutoTune button for 0.5 seconds and then release. 8. When the waveband end is reached your radio will recommence tuning from the opposite waveband end. 9. Adjust the Volume control to the required settings. 10. To switch off your radio press the StandBy button. 9 9 10 If you need any further advice, please call our Technical Helpline on :020 8758 0338 (Mon-Fri) Manual tuning - FM 1. Press the StandBy button to switch on your radio. 2. Press the FM/DAB button to select the FM band. Fully extend the Telescopic aerial . 3. Press the Tuning up or down buttons to tune to a station. The frequency will change in steps of 50kHz. 4. When the waveband end is reached the radio will recommence tuning from the opposite waveband end. 5. Set the Volume control to the desired setting. 6. To switch off your radio press the StandBy button. 1 2 3 3 5 5 6 Display modes - FM On FM the bottom line of the display can be set to any of the following modes:a 1. Press the Info button to cycle through the various modes. a. Scrolling text Displays scrolling text messages such as artist/track name, phone in number etc. b c b. Program Type Displays type of station being listened to e.g. Pop, Classic, News, etc. c. Signal strength Displays signal strength for station being listened to. d d. Time and date Displays current time and date. e e. Frequency Displays frequency of the station being listened to. f f. Audio mode Display shows Auto (stereo) or mono. 1 FM Stereo/Mono 1. If a station being received is weak some hiss may be audible. To reduce the hiss press and hold in the Select button until the display shows "Audio mode : mono" your radio will switch to mono mode. 2. To return to stereo mode ...