Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
To turn off the alarm until the next day press the Alarm/Off button. To turn off the alarm permanently set the Function switch to the 'Off' position. Off Buzz Auto On PM If you need any further advice, please call our Technical Helpline on : 020 8758 0338 (Mon-Fri) Snooze control The radio or buzzer alarm Snooze button. This sequence can hour 59 min). The Snooze control can also Remote - see following page. Alarm / Off Sleep timer The radio can be set to turn off after a preset Press and hold down the Sleep button until the desired time is reached (maximum 59 minutes in 1 minute steps). The radio the sleep time has elapsed. To increase the sleep time depress the hour button once whilst holding down the Sleep button. The clock will display the sleep time 1:59. To cancel the sleep function before the preset time has expired, PM the Snooze button. The sleep function can also be cancelled via the Pillow Talk Remote - see following page. Alarm / Off Dimmer Dimmer Switch High Low The Dimmer switch located on the left side of your clock radio will allow you to adjust the intensity of the clock display to suit room brightness. Headphones (on rear) A Headphone Socket (3.5mm) is provided for use with either headphones or an earpiece. Inserting a plug automatically mutes the internal loudspeaker. Pillow Talk Remote Your Pillow Talk Remote cancel functions. The built radio or wake up to the radio partner. Ideal for listening to the 1. Insert the plug from the Pillow Talk Remote Headphone socket on the rear of your clock radio, the internal automatically muted. 2. Place the Pillow Talk Remote under your Pillow with loudspeaker grille uppermost. 3. Switch on the radio by sliding the Function switch to the 'On' position. 4. Adjust the Volume control to a comfortable level. 5. The radio or buzzer alarms can be set and operated as previously described, the only difference being that sounds will be via your Pillow Talk Remote. Remote snooze control 1. The radio or buzzer alarm can be silenced for 9 minutes by pressing the Snooze button on the Pillow Talk Remote. This sequence can be repeated during the alarm cycle (1 hour 59 min). Remote sleep timer cancel 1. To cancel the sleep function before the preset time has expired, press the Snooze button on the Pillow Talk Remote. TMZPillowTalkTM If you need any further advice, please call our Technical Helpline on : 020 8758 0338 (Mon-Fri) General Do not allow this unit to It is recommended that the FM band be used of quality and freedom from on the MW or LW bands. Mains supply The CR9920 will operate from a supply only. For your convenience this product is supplied with a plug which is with a fuse of the appropriate rating. If the plug for your socket outlet, it should be removed by unscrewing the terminal screws, and removing the cable. The correct style of plug to suit your household together rated fuse should be fitted. IF IN DOUBT - CONSULT A QUALIFIED ELECTRICIAN IMPORTANT. DO NOT make any connection to the larger terminal which is marked with the letter E or by the safety earth symbol or coloured Green or Green-and-yellow. The wires in the mains lead are coloured in accordance with the following codes : BLUE - NEUTRAL BROWN - LIVE As these colours may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: E L N 3 amp Brown (Live) (Neutral) (Earth) Cord The wire coloured BLUE must be connected to the terminal marked N or coloured BLACK. The wire coloured BROWN must be connected to the terminal marked L or Blue coloured RED. Fuse This apparatus must be (BS1363). If another type plug, adaptor or distribution IF IN DOUBT - CONSULT A QUALIFIED Back-up Battery (not necessary Slide the battery cover catch in the direction cover. Fit a 9 volt IEC size 6LR61 (6F22, PP3) battery into the compartment. Replace the battery cover. The time and alarm settings will be retained during AC mains supply. The LED display will not be operational. be extinguished to conserve battery life. (Underside) Specifications Circuit Features Power Requirements Loudspeaker 75mm diameter 8 ohms Mains AC 230 volts, 50Hz only Back-up Battery IEC size 6LR61 (6F22, PP3) Output Power 0.3W RMS Frequency Coverage Aerial System FM Wire Aerial FM 87.5 - 108MHz MW 525 - 1610kHz MW Built-in Ferrite aerial LW 147- 284kHz LW Built-in Ferrite aerial ROBERTS RADIO LIMITED PO BOX 130 MEXBOROUGH SOUTH YORKSHIRE S64 8YT The Company reserves the right to amend the specification without notice. If you need any further advice, please call our Technical Helpline on : 020 8758 0338 (Mon-Fri) Guarantee This instrument is guaranteed or component breakdown, subject to the or replaced free of charge. The guarantee does not cover: 1. Damage resulting from incorrect use. 2. Consequential damage. 3. Receivers with removed or defaced serial Procedure: Any claim under this guarantee should be made through Roberts' dealer will be able to attend to any defect quickly and efficiently, but should c...