Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Setting the brightness of the display Three levels of brightness are available by pressing SNOOZE/BRIGHTNESS. High (default) t Middle t Low Playing the iPod You can enjoy iPod audio by connecting this unit. To use an iPod, refer to the user’s guide of your iPod. Compatible iPod models The compatible iPod models are as follows. Update your iPod to use the latest software before you use it. Notes • The connector of the unit is for sole use for iPod. When you use the devices do not match with the connector, connect it to the AUDIO IN terminal of this unit with the supplied audio connecting cable. • Sony cannot accept responsibility in the event that data recorded to iPod is lost or damaged when using an iPod connected to this unit. 1 Put the iPod into the unit’s connector. Adjust the rear support forward or backward checking the back of the iPod fits snugly against the rear support to protect the connector. 2 Press N/X. The iPod begins to play automatically. You can operate the connected iPod by the unit or iPod buttons. * These operations are available only when using the supplied remote commander. Notes • When placing or removing the iPod, keep it straight and parallel with the rear support. • Do not carry the unit with an iPod set on the connector. Doing so may cause a malfunction. • When placing or removing the iPod, brace the unit with one hand and take care not to press the controls of the iPod by mistake. • Do not pull on the rear support strongly as it cannot be detached from the unit and may cause a malfunction. • To use an iPod, refer to the user’s guide of your iPod. • Before disconnecting the iPod, pause playback. Tip Apple’s iPod Universal Dock Adapter can be used with this unit. To use the unit as a battery charger You can use the unit as a battery charger. The charging begins when the iPod is placed on the connector. The charging status appears in the iPod display. For details, see the user's guide of your iPod. On copyrights • iPod is a trademark of Apple Inc., registered in the U.S. and other countries. • All other trademarks and registered trademarks are of their respective holders. In this manual, ™ and ® marks are not specified. Playing the radio —Manual Tuning 1 Press RADIO ON to turn on the radio. The display shows the band and frequency. 2 Press RADIO ON repeatedly to select the desired band. Each press changes the band as follows: FM1 FM2 AM FM1 and FM2 are the same frequency bands. 3 Use TUNING + or – to tune into the desired station. The FM frequency advances or reverses in 0.1 MHz channel steps and the AM frequency in 10 kHz channel steps. 4 Adjust volume using VOLUME. To turn off the radio, press OFF. Improving the Reception FM: Extend the FM wire antenna fully to increase reception sensitivity. AM: Connect the supplied AM loop antenna to the unit. Rotate the antenna horizontally for optimum reception. Keep away iPod from the AM loop antenna or the FM wire antenna, as this may lead to interference of reception. Tip If the FM broadcast is noisy, press FM MODE on the remote commander to turn off “STEREO” in the display. The radio becomes clearer although the sound becomes monaural. Presetting Your Favourite Station —Preset Tuning You can preset up to 10 stations in FM (5 stations in FM1, 5 stations in FM2), and 5 stations in AM. Presetting a Station 1 Follow steps 1 to 4 in “Playing the Radio” and manually tune into the station you wish to preset. 2 Press and hold the desired PRESET TUNING button for more than two seconds for registration. After the preset has finished, the preset number appears on the display. Example: To preset AM 1 260 kHz onto preset 2 button. a few seconds after v To preset another station, repeat these steps. To change the preset station, tune into the desired station and hold down the PRESET TUNING 1 to 5 button. The new station will replace the previous station on the preset button. Tuning into a preset station 1 Press RADIO ON to turn on the radio. 2 Press one of the PRESET TUNING buttons where the desired station is stored. 3 Adjust volume using VOLUME. Setting the alarm The dual alarm function allows you to set two alarm programs (ALARM A and ALARM B). The alarm time can be set for each program and the alarm sound is selectable from RADIO, BUZZER or iPod. Notes • Before setting the alarm, make sure to set the clock (see “Setting the clock and date”). • The factory setting alarm time is “AM 12:00”. • To set the radio alarm, first tune in to a station (see “Playing the radio”). To set the alarm time To set ALARM A 1 Press ALARM SET A for a few seconds. 2 Press TIME SET +/– to set the desired hour, and press ALARM SET A. 3 Press TIME SET +/– to set the desired minute, and press ALARM SET A. 4 Press TIME SET +/– to set the desired alarm mode (RADIO, BUZZER or iPod) and press ALARM SET A. 5 If you select the RADIO or iPod, press TIME SET +/– to set the wake up volume and press ALARM SET A. To set ALARM B, follow the same steps above using ALARM B instead of ALAR...