Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
Effective range of the infrared rays (See ill. A) The effective range of the infrared rays emitted from the infrared dome of the Dream Machine is approximately 5 m (16 ft.) with a vertical angle of approximately 40°. Make sure to place your TV, cable or VCR unit so that the infrared ray sensors are located within this range. Notes on optimal location • Place the Dream Machine in an area with a direct line of sight from your TV, cable or VCR unit. Remove any object that might obstruct the direct line between the infrared dome of your Dream Machine and the infrared ray sensor. • Do not place the Dream Machine in an area subject to direct sunlight or under any strong illumination. The ominidirectional infrared ray system may not operate properly. • Do not use any other infrared ray remote control device simultaneously with the Dream Machine. An interference may occur and the unit may not operate properly. Setting Up the Remote Control Function Complete this built-in pre-programmed ON/OFF remote control setup before you proceed to the next section. This will enable the successful remote control of your TV, cable or VCR unit from your Dream Machine. The built-in pre-programmed remote control setup will guide you in determining the compatible infrared ray signal for your TV, cable or VCR unit. 1 Turn on the power of the desired component (your TV, cable or VCR unit) you wish to control remotely. 2 Select TV or CABLE/VCR accordingly. 3 Press REMOTE POWER on the Dream Machine. If the power of the desired component turns off, you have successfully completed the built-in pre-programmed ON/OFF remote control setup. If not, proceed to the next step. 4 While holding down REMOTE POWER, press BRAND SELECT. If the power of the desired component turns off, you have successfully completed the built-in pre-programmed ON/OFF remote control setup. If not, repeat this step until the power of the desired component turns off. If the power component beep sounds The infrared ray signals transmitted to the component location of the Dream Machine. Dream Machine to an optimal desired component is within the of the infrared rays and is free from After relocating the Dream Machine, 1 to 4 once again. To check the remote control function TV unit: Select TV and press REMOTE POWER. If a compatible signal for your TV unit is transmitted, your TV unit will turn on. Cable or VCR unit: Select CABLE/VCR and press REMOTE POWER. If a compatible signal for your cable or VCR unit is transmitted, your cable or VCR unit will turn on. TV and cable or VCR units: Select TV+CABLE/ VCR and press REMOTE POWER. If a compatible signal for your TV and cable or VCR units is transmitted, your TV and cable or VCR units will turn on at the same time. Setting the Clock and the Date Setting the Clock 1 Plug in the unit. “AM 12:00” flashes in the display. 2 While holding down CLOCK, press TIME SET+,– repeatedly until the correct time appears in the display. When you release CLOCK, the clock begins to operate. • To set the current time rapidly, keep pressing the + or – button while holding down CLOCK. Setting the Date 1 While holding down SNOOZE/DATE/ SLEEP OFF, press TIME SET+,– repeatedly until the correct date appears in the display. Then, release SNOOZE/DATE/SLEEP OFF. • To display the date, hold down SNOOZE/ DATE/SLEEP OFF. When you release SNOOZE/ DATE/SLEEP OFF, the display returns to the current time. Playing the Radio 1 Press RADIO ON/SLEEP to turn on the radio and adjust VOL. 2 Select FM or AM, and tune in to the desired station using the TUNING dial. • To turn off the radio, press RADIO OFF. • To improve radio reception FM: Extend the FM wire antenna fully. AM: Rotate the unit horizontally for optimum reception. A ferrite bar antenna is built into the unit. Setting The Dream Machine enable the setting of Alarm Alarm B (radio or buzzer). Setting Alarm A (Remote) To set your TV, cable or VCR unit, first select desired channel and adjust the volume. Before you proceed, make sure you have successfully completed “Setting Up the Remote Control Function". 1 Select TV, CABLE/VCR or TV + CABLE/ VCR. 2 While holding down ALARM A, press TIME SET+,– until the desired time appears in the display. When ALARM A is released, the ALARM A indicator and “:” will stop flashing and light up. The current time will appear in the display. The remote function will activate the desired components at the preset time and turn off automatically after 59 minutes. Notes • When Alarm A is set, the simultaneous use of any other infrared ray remote control device with the Dream Machine may lead to an interference and the unit may not operate properly. • When your TV or VCR unit is on at the preset time of Alarm A, your TV or VCR unit may turn off inadvertently depending on the model. Setting Alarm B (Radio or Buzzer) To set the radio, first tune in to the desired station and adjust the volume. 1 Select RADIO or BUZZER. 2 While holding down ALARM B, press TIME SET+,– until the desired time a...