Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
5 PSS100B_ManualEN_082807.qxp 9/13/07 5:32 PM Page 6 USING THE RADIO Refer to the enlargement of the Clock/Radio Panel below to locate referenced buttons and controls. CLOCK/RADIO PANEL (DETAIL VIEW) By default, the Digital Display shows the time. Pressing the Radio ON/OFF Pushbutton ( ) toggles between turning the Radio ON and OFF. When it is ON, the LCD Display shows the currently selected frequency and station. Note that the back light will activate automatically whenever any button is pressed. Press the BAND/MODE Pushbutton to cycle through to the desired frequency (AM, FM or AU [digital audio player] mode). Use the TUNING Pushbuttons ( or ) to cycle up or down to the desired station. Use the VOLUME Pushbuttons (+ or – ) to select desired volume. The Digital Display will briefly show selected volume level (from 0 to 30). Programming Stations Into Memory Up to 10 stations can be programmed into memory. • Press the Radio ON/OFF Pushbutton to turn the Radio ON. • Press the BAND/MODE Pushbutton to cycle through to the desired frequency (AM or FM). • Use the TUNING Pushbuttons ( or ) to cycle up or down to the desired station. • Press and hold the MEM/CLOCK Pushbutton until a blinking “M” appears on the Digital Display. • Press the TUNING Pushbutton ( or ) to select the desired memory station number. • Press the MEM/CLOCK Pushbutton to save the setting. • Repeat this process (up to 9 times). Stations will be accessed in the order they were programmed in. To Access User-Programmed Stations: • Press the Radio ON/OFF Pushbutton to turn the Radio ON. • Press the BAND/MODE Pushbutton to cycle through to the desired frequency (AM or FM). • Press the MEM/CLOCK Pushbutton to cycle through all programmed stations until desired memory number appears. USING THE MP3/DIGITAL MUSIC PLAYER COMPARTMENT/CABLE PLUG The PSS100B comes with an MP3/Digital Music Player Compartment (top of unit – refer to the illustration to right) and built-in Input Cable Plug. To play music from an MP3 or digital musicPlayer: 1. Lift the MP3/Digital Music Player Compartment cover door up (refer to the illustration to locate). 2. Insert the built-in Input Cable Plug into the headphone jack on audio player device. 3. Open the spring loaded bracket and set the audio player device into place. 4. Release the spring loaded bracket slowly to secure the audio player device. 5. Place the unit into auxilliary input (AU) mode by pressing the BAND/MODE button. 6. Operate the MP3/Digital Music Player as usual. 7. Use the VOLUME Pushbuttons (+ or – ) to select desired volume. The Digital Display will briefly show selected volume level (from 0 to 30). 6 PSS100B_ManualEN_082807.qxp 9/13/07 5:32 PM Page 7 8. Close the MP3/Digital Music Player Compartment cover door. Note: MP3/Digital Music Player and USB charging cables are not included. If you want to recharge the MP3/Digital Music Player while it is playing, plug the device’s USB charging cable into the USB Power Port inside the MP3/Digital Music Player Compartment and press the USB Charging Port ON/OFF Pushbutton to turn the USB Ports ON. USING THE 120 VOLT AC POWER SUPPLY The unit comes with: 1. AC Power ON/OFF Pushbutton — Press pushbutton to turn the AC Power Supply ON and OFF. 2. Dual 120 Volt AC Power Outlets. 3. AC Power Supply Status Indicator LEDs — both green and red light when AC outlet is turned on and ready to use; red light only indicates the inverter is overloaded or faulted. 4. AC Power Electrical Fault Circuit Interruptor— two three-prong outlets for 110/120 volt AC appliances which shut down inverter if leakage or ground fault current is detected. 5. Internal protective circuits including: • Overload and over-temperature shutdown (activated if AC output exceeds 100 watts or the unit overheats) • AC short-circuit shutdown • Low voltage shutdown (shuts down inverter when internal battery voltage is too low) AC Power Supply Controls, Indicators and Operation The illustration in the previous section details the AC Power Supply Panel. The AC Power ON/OFF Switch turns the AC power circuitry ON and OFF. It can also be used to reset AC power after shutdown due to overvoltage, overload or over-temperature condition. Both Status Indicator LEDs light when AC power supply is available. 1. Press the AC Power ON/OFF Pushbutton to turn the AC Power Supply ON (both Status Indicator LEDs light). 2. Plug in appliance (rated up to 100 watts) and operate as usual. Make sure the 120 Volt AC Power Supply is turned OFF when the unit is being recharged or stored. The standard North American 120 volt AC outlets and USB ports allow simultaneous operation of multiple devices. Simply plug the equipment into the unit’s AC outlets and operate normally. Ensure that the wattage of all equipment simultaneously plugged into the unit’s 120 Volt AC Outlets does not exceed 100 watts continuous. Notes: The AC power supply shuts down automatically when the battery voltage level is too low. If only the red Status Indicator LED ligh...
Dieses Handbuch ist für folgende Modelle:Radios - 90521849 (511.66 kb)