Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
The power supply connector is 5.5mm/2.1mm x 13mm long, center positive. Do not connect the power supply to an electrical outlet controlled by a wall switch. It is normal for the power supply to become warm during use. An optional 12VDC nominal, 1.5A fused source may also be used. 3. TIME SET: Briefly press and release this button to advance the hands in small increments. Press and hold this button to continuously advance the clock’s hands. Release the button when the clock is set properly. Be sure the alarm button is in the Off position when setting the time. See “How to set the clock”. 4. ALARM GRILLE: The alarm beep emits from this grille. Do not block this grille. 5. BATTERY BACK UP: Remove the battery cover and install a fresh major brand 1.5V “AA” battery, observing correct +/– polarity. The clock operates off of the battery continuously and the battery also acts as a back up. In the event of a power failure, the battery back up will maintain the clock’s operation and sound the wake-up tone if the alarm button is in the On position, provided a fresh battery is correctly installed. The clock face will not illuminate and the radio will not operate during a power failure in order to conserve battery life. Check the battery’s strength annually and replace only with a major brand, 1.5V “AA” alkaline battery. If the clock stops operating, replace the battery. To reduce the risk of fire or injury, do not leave a dead battery in the clock. Do not dispose of the spent battery into a fire. Do not open or tamper with the battery. Do not recharge the supplied battery. Dispose of the spent battery according to your state/country's regulations. Remove the battery if the Dual Alarm is to be stored or unused for a long period of time. How To Set The Clock Set the hands to the correct time with the Time Set button. Push the Time Set button in and release to move the hands in small increments or hold the button in to continuously advance the hands. Be sure the front panel alarm button is in the OFF position when adjusting the time. How To Set The Alarm 1. Rotate the alarm thumbwheel counter-clockwise and set the alarm hand to the approximate time you wish to wake to. DO NOT TURN THE ALARM BEZEL CLOCKWISE OR YOU MAY DAMAGE THE MECHANISM. 2. Press the Alarm button ON and the green alarm LED will light. The alarm tone activate when the clock time roughly coincides with the setting of the alarm hand. 3. To turn the Alarm OFF, press the Alarm button again and the Alarm LED will extinguish. The Dual Alarm Speaker can be set to wake to the alarm tone only. Important Note: Due to the nature of the alarm thumbwheel’s analog mechanism, which was designed for simplicity, there can be up to a five-minute deviation from when the alarm activates. For example, if the alarm is set for 10:00, it is possible it could activate at 9:55 or 10:05. We recommend you set the alarm early the first time you use it to accommodate for this. As you use your Dual Alarm Speaker you will get a better idea of where you need to set the alarm in order to wake-up at the desired time. Placement Placing your Dual Alarm Speaker inside a bookshelf or against a wall will inflate the bass as well as confine the speaker’s output. For best sound reproduction, allow the sound from the speaker to emit without restriction. Do not place objects over the speaker grille. Do not obstruct the rear bass port. The Dual Alarm Speaker is magnetically shielded but it is best kept at least 5” away from a computer monitor or television set. Cleaning Never use harsh cleaners or solvents or abrasive pads. The face may be cleaned with a slightly damp, soft cloth. Take care not to rub too hard. For the wood cabinet, liquid polish usually yields better results than spray-on waxes. Do not use glass cleaner or other chemicals to clean the clock’s window. Painting or staining the cabinet is not recommended and will void your warranty. Since the cabinet is natural wood, it is not always possible to achieve an exact color/grain match between the main unit and other Tivoli Audio products. You may also notice the wood darken over time. Warranty Tivoli Audio manufactures its products to very high standards and we are confident our products will perform well. Accordingly, we warranty this product against manufacturing defects in material and workmanship to the original owner, for a period of one year from the original date of purchase. This warranty is non-transferable. This warranty does not extend to damage caused by improper use/installation, faulty ancillary equipment, modifications, unauthorized repair, shipping damage or loss, abuse, accidents, use on improper voltage/current, power surges, lightning or other acts of God, normal wear and tear, or commercial use. Please consult the dealer from which you purchased this product for warranty service or repair. Proof of purchase may be required. Please resist the temptation to take apart this product. There are no user serviceable parts insi...