Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Magnavox, modell AJ 3140

Hersteller: Magnavox
Dateigröße: 367.34 kb
Dateiname: b7753b10-4e47-4225-8a1e-6536302fb6ed.pdf

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Setting alarm time 1 and 2 1. Press and hold down the ALARM 1 or ALARM 2 button to set the alarm time. 2. Use the 4 and 7 buttons to set and adjust the hours and minutes. – With 7 pressed; the time will increase rapidly from minutes to hours. Release 7 when you have reached the correct setting. – Pressing 4 will allow you to adjust the time backward minute by minute. 3. Release the ALARM 1 or ALARM 2 button and the 7 or 4 buttons when you have reached the correct setting. – The clock display goes back to clock time. To review your set alarm time, press the appropriate ALARM 1 or ALARM 2 button. The clock radio can wake you in two ways: Wake by radio: 1. Tune to the desired radio station using the TUNING knob. Make sure you have adjusted the volume loud enough to wake you up. 2. Set the ALARM 1 mode or ALARM 2 mode selector to RAD(io). – The respective ALARM indicator lights up on the display. At the set alarm time, the radio will switch on and it will automatically switch off 59 minutes later. Wake by buzzer: 1. Set the ALARM 1 mode or ALARM 2 mode selector to BUZ(zer). – The respective ALARM indicator lights up on the display. At the set alarm time, the buzzer will switch on and it will automatically switch off 59 minutes later. There are three ways to switch off the alarm. Switching off the alarm for 24 hours 1. Press the RESET button. – The alarm is now switched off for 24 hours and will sound again the next day at the same time. Switching off the alarm temporarily For both alarm modes (radio or buzzer) this will repeat your alarm at seven minute intervals. 1. Press the SLUMBER OFF/REPEAT ALARM button. – The alarm will temporarily switch off. Seven minutes later, the alarm (radio or buzzer) will sound again. 2. Press the SLUMBER OFF/REPEAT ALARM button again if you wish to repeat the alarm call. – If the SLUMBER OFF/REPEAT ALARM button is not pressed again, the alarm will automatically switch off 59 minutes later. Your alarm time setting will then automatically enter the RESET mode and will sound at the same time the next day. Switching off the alarm completely 1. Push the ALARM 1 mode or ALARM 2 mode selector to the OFF position, before or during the set alarm time. – The alarm indicator will disappear from the display. ALARM OFF ALARM ON SETTING THE ALARM If a fault occurs, first check the points listed below before taking the set for repair. If you are unable to solve a problem by following these hints, consult your dealer or service center. WARNING: Under no circumstances should you try to repair the set yourself, as this will invalidate the warranty. Alarm 1. Check if the AC power voltage as shown on the type plate on the back of the set corresponds to your local AC power supply. If it does not, consult your dealer or service organization. 2. Connect the power plug to the wall outlet. – The power supply is now switched on and the numbers on the display will start to flash. You will need to set the correct time. 3. To disconnect the set from the AC power completely, withdraw the power plug from the wall outlet. – When a power failure occurs, the clock radio will be switched off. – When the power supply returns, the numbers on the display will start to flash and you will need to reset the correct time on the clock. – To retain the clock time and the set alarm time(s) in the event of an AC power failure or disconnection, you can insert a 9 volt battery (not included), type 6F22, into the battery compartment. Should there be a power failure, the clock will continue to function. However, the time will not be illuminated on the clock display, as the use of the battery is strictly to retain both the set clock and alarm time(s) only, where actual operation of the alarm and radio is excluded. As soon as the power is switched on again, the display will indicate the correct time. 1. Before inserting the battery, connect the power plug to the wall outlet. 2. Place the battery in the battery compartment on the bottom of the clock radio. – Replace the battery once a year, or as often as necessary. Clock display The time is displayed using the 12-hour clock system where the PM indicator lights up (on=PM, off=AM) in the top left corner of the display. The display also indicates whether you have switched on the alarm(s). These indicators will light up respectively next to ALARM 1 and ALARM 2 on the display. 1. Press and hold down the TIME button. 2. Use the 4 and 7 buttons to set and adjust the hours and minutes. – With 7 pressed: the time will increase rapidly from minutes to hours. Release 7 when you have reached the correct setting. – Pressing 4 will allow you to adjust the time backward minute by minute if necessary. You can use this clock solely as a radio 1. Set the RADIO switch to ON. 2. Select your wave band using the BAND switch. 3. Locate the required radio station using the TUNING dial. 4. Set the volume by turning the VOLUME knob. 5. To turn off the radio, set the RADIO switch to OFF. Antenna: – For FM r...