Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
Mast (Not Included) Reflector Booms Front Boom Boom Brace Large Boom Rear Boom Step 1: Unpack Remove all three sections of the antenna and the hardware bag from package. Make sure the following parts are in the package: • (3) Antenna sections (rear, large/middle, and front booms) • (1) Boom brace • (2) Refl ector booms • (1) Hardware bag The hardware bag contains the following pieces: (2) U-Bolts (4) 1/4” Flange nuts (2) Mast clamp inserts (5) End caps (10) #10 Flange nuts (4) #10 Screws (8) #10 Washers (1) Matching transformer BEFORE YOU START!!! Please read the IMPORTANT SAFETY INFORMATION sheet included in this package. Assembling the ANT3038XR Fig.1: ANT3038XR fully assembled (mast not inclued) English 2 IMPORTANT: Unfold the elements on each end of the refl ector boom so that the front of their locking tabs face towards each other. The remaining locking tabs can be unfolded in either direction. Make sure that all of the elements are perpendicular to the refl ector boom. Connect the two refl ector booms to the front boom using two of the provided #10 nuts and screws. The refl ector booms should be parallel to the smaller boom at this point. (See Fig. 1.) Fig. 2 Step 2: Connect the refl ector booms to the front (small) boom Find the two refl ector booms and the front (or small) boom. The two smaller elements on the refl ector booms face away from the small main boom. Fig. 1 Step 3: Unfold the rest of the antenna Unfold all the other elements on the antenna until they lock into place ensuring that they are fl at and parallel to each other. (See Fig. 3.) Fig. 3 Fig. 2A FRONT Locking Tab Main Boom English Step 4: Connect the middle (large) section to the front (small) section Find the middle (large) section. Locate the end of the middle section that matches figure 4. Remove the nut and screw in the center. Slide the narrow boom of the front (small) section into the middle (large) section. Make sure the phasing lines are on the top side of the small boom and the black plastic element holders are also on this same side. This is the top of the antenna. (See figure 5.) Tap lightly with a rubber mallet on the end of the small boom aligning the holes for the screw. (See figure 4.) Re-install the screw and nut; be sure to tighten securely. Step 5: Connect the phasing lines Place the phasing lines from the front section over the studs. Secure them to the studs with #10 flange nuts and washers. Tighten securely. Fig. 4 Front section Middle section Phasing Lines Fig. 5 3 4 On the open end of the middle (large) section, remove the rear nut and screw. Find the rear section. Slide the narrow boom of the rear antenna into the middle (large) section. Tap lightly with a rubber mallet on the end of the small boom, aligning the holes for the screw. (See fi gure 6.) Re-install the screw and nut; be sure to tighten securely. Step 6: Connect the rear section to the middle (large) section Rear section Middle section Screw Nut Fig. 6 Step 7: Connect the phasing lines On the middle (large) section, near where the middle and rear sections come together, fi nd the posts on the top and bottom of the last element holder studs. (See fi gure 7.) Place the phasing lines from the rear section over the studs, one on the top side and one on the bottom. Then fasten them to the posts with washers and #10 fl ange nuts. Tighten securely. Nut Washer Stud Phasing line Fig. 7 5 Step 8: Connect the boom brace Lay the boom brace on top of the antenna. Make sure the mast clamps (the brass-colored sections) on the boom brace and antenna are facing the same direction. Locate the screw hole in the refl ector boom and attach the brace with one of the provided #10 screws and nuts. (See fi gure 8.) Screw Nut Fig. 9 Fig. 8 Step 9: Install the transformer Find the downlead connection on the bottom of the front section of the antenna, just beyond the refl ector booms. Place two washers on each of the studs. Place a #10 nut on top of each stud, but don’t tighten them yet. Place the transformer ends between the two washers and tighten the nuts securely. (See fi gure 10.) Attach the coax downlead to the transformer. Transformer Downlead connections Fig. 10 Swing the boom brace down towards the rear. Form a “V” with the metal straps. Use one of the provided #10 screws and nuts to attach the “V” to each side of boom. (See fi gure 9.) English Step 10: Insert end cap s Fig. 11 Insert two of the plastic end caps in the ends of the antenna as shown in figure 11. Insert a third plastic end cap in the exposed end of the boom brace. Insert the last two end caps on the ends of the refl ector booms. Use a rubber mallet to gently tap them into the ends so that they are secure. Step 11: Mount the antenna to a mast Find the two U-bolts, four 1/4” flange nuts, and the two mast clamp inserts. Place the mast clamp inserts on the inside of the mast clamps on the antennas as shown in figure 12. Then insert the U-bolts into the mast clamps and mast clamp inserts. Attach the nuts lo...