Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
• Do not place lighted candles, cigarettes, cigars, etc. on the product. • Connect power cord only to AC power source as marked on the product. • Care should be taken so that objects do not fall into the product. • Do not attempt to disassemble the cabinet. This product does not contain customer serviceable components. • IF YOUR PRODUCT OPERATES ON BATTERIES, adhere to the following precautions: A. Any battery may leak electrolyte if mixed with a different battery type, if inserted incorrectly, or if all batteries are not replaced at the same time. B. Any battery may leak electrolyte or explode if disposed of in fi re or an attempt is made to charge a battery not intended to be recharged. C. Discard leaky batteries immediately. Leaking batteries can cause skin burns or other personal injury. When discarding batteries, be sure to dispose of them in the proper manner, according to your state/provincial and local regulations. user manual guide de l’utilisateur RC46 v1.0 (EN/F) The descriptions and characteristics in this owner’s manual are for the purpose of general reference only and not as a guarantee. In order to provide you with the highest quality product, we may make changes or modifi cations without prior notice. Before you begin Clock WARNING: TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. SEE MARKING ON BOTTOM OF PRODUCT EN/F It is important to read this user manual prior to using your new product for the fi rst time. Nous vous recommandons de lire ce manuel d’instructions avant d’utiliser votre nouveau produit pour la premiere fois. MHz AM PM AM FM kHz AUX PLEASE READ AND SAVE THIS FOR FUTURE REFERENCE IMPORTANT SAFETY INSTRUCTIONS ] Plugging in for power AC OUTLET POWER SUPPLY: 120V~60Hz Refer to the “Clock” section and follow the instructions to get the clock time shown correctly with the Auto Clock set feature. Battery back-up operation • This clock radio is equipped with a memory holding system that can be powered with 2 “AA” batteries (included). The power failure protection circuit will not operate unless battery is installed. • When normal household power is interrupted, or AC line cord is unplugged, the batteries will power the clock radio to keep track of time and alarm settings programmed into memory. • When the battery backup functions, the digital display will not light, however, the function of alarm still occurs during the power interruption if remaining battery power is adequate. • Normal operation will resume after AC power is restored so you will not have to reset the time or the alarm. To install batteries: 1. Remove battery compartment door (located at the bottom of the radio) by applying thumb pressure to the tab on battery door and then lift the door out and off the cabinet. 2. Insert 2 AA batteries (included). 3. Replace the compartment door. Note: we recommend that you replace the batteries every year. Power failure indicator When AC power is interrupted (disconnected) for a short period of time, both time and alarm settings will change (unless batteries are installed). After AC power is restored (reconnected), the Digital Display will blink to indicate that power was interrupted and you should readjust the time and alarm settings. Power is fed to the unit even when it is not functioning. To cut the power supply off, the power cable must be unplugged. Front view SNOOZE – enter snooze mode where the alarm will quiet but sound again once the snooze period is over. RADIO – turn on the radio. REV – set clock or wake time (decrease value). FWD – set clock or wake time (increase value). OFF – turn off the unit. CHECK WAKE TIME – check the currently set wake time. –VOLUME+ – adjust volume. TUNING – select radio frequencies. General controls Back view BRIGHTNESS – select display brightness (high or low). DST – turn daylight saving function on or off. TIME ZONE – press repeatedly to select a time zone BAND – select between AM and FM bands. Top view SLEEP – activate sleep function. /WAKE1/WAKE2/ – slide switch to set Wake 1, Wake 2 and clock time. WAKE – OFF – activate and set wake function. MHz AM PM AM FM kHz AUX Setting clock manually 1. Slide the switch /WAKE1/ WAKE2/ on the top of the unit to clock position. 2. Press REV or FWD to set the clock time. The time decrements or increments will follow by a faster rate when you press and hold the buttons. • The “:” between hour and minute time fl ashes when you are setting the time. AM or PM icon will also show beside the time. 3. Slide the switch /WAKE1/ WAKE2/ on the top of the unit to lock position when fi nished. Auto clock set US time zones You do not have to set the clock time as a built-in automatic time set system is equipped in this clock powered by 2 AA batteries (included and installed). To set the clock time correctly: 1. Plug for power • Insert the plug of the unit into an AC power outlet. 2. Select daylight saving • Slide the DST switch at the back of the unit to turn on/ off in ar...