Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
The radio is now on and you can LARGE DISPLAY in the usual way. Play will be for the chosen length of time 1. Plug the power cord into any 120V AC household (up to 1 hour 59 minutes), and then the radio For Your Safety 2. Slide the FUNCTION switch to ON to turn on the off. If you decide to turn the radio off sooner, press the The AC power plug is polarized (one blade is wider AM/FM CLOCK RADIO AM SNOOZE button. 3. Slide the AM/FM BAND switch to desired broadcast Indicator other) and only fits into AC power outlets one way. If the plug Volume 4. Turn TUNING knob to select a station. won’t go into the outlet completely, turn the plug over and try Knob to insert it the other way. If it still won’t fit, contact a qualified 5. Adjust the VOLUME knob to your preferred listening level. AM/FM sleep to music and wake to music or alarm electrician to change the outlet, or use a different one. Do not 6. To turn the radio off, slide the FUNCTION switch to OFF. Band attempt to bypass this safety feature. You can set your digital clock radio to lull you to sleep, turn itself Switch Tuning off, then awaken you at a preset time - all automatically. Knob Built-in AFC Important Battery Information 1. Set the wake time. The Built-In Automatic Frequency Control (AFC) works only on 2. Follow the steps under WAKE TO MUSIC or WAKE TO ALARM. • When storing the unit or unplugging it from AC outlet for a WAKE FM. It helps to reduce drift on FM reception and to keep the day or more, be sure to remove battery because it can leak 3. Then, proceed with Steps 2 through 4 under SLEEP TO MUSIC. Indicator radio locked in on the FM station to which it is tuned. and damage the unit. When tuning in FM stations, you may notice that often the • Batteries may leak electrolyte if inserted incorrectly, if station you desire can be heard on two or three nearby points on Snooze Alarm Operation disposed of in fire, or if an attempt is made to charge a the dial. Always tune carefully to the loudest and clearest point. The Snooze-Alarm button has three functions: battery not intended to be recharged. 1. It allows extra sleep time after the radio comes on in the • Discard leaky batteries immediately. Leaking batteries can Antennas WAKE TO MUSIC mode. Press SNOOZE button to silence the AM Antenna - A built-in ferrite rod antenna eliminates the need cause skin burns or other personal injury. radio. About 9 minutes later, the radio will play again. • Dispose of batteries, according to federal, state, and local for an outside antenna for AM reception - Rotating the unit 2. It allows extra sleep time in the WAKE TO ALARM mode. regulations. slightly may improve reception of distant AM stations. When the alarm sounds, touch the SNOOZE button to silence FM Antenna - The power cord acts as your FM antenna. The the alarm. About 9 minutes later, the alarm will sound again. Sleep Button You can use the SNOOZE feature repeatedly for up to two power cord picks up moderate to strong stations and eliminates hours, after which the radio or alarm will turn off until the sure the power cord is stretched out to its full length. Do not coil the need for an external antenna in most strong signal areas. Be Wake Set/Off next day. Button or bunch the cord together. Changing position of the power cord 3. It shuts off the sleep cycle. (See SLEEP TO MUSIC). may improve reception. “No Worry Battery Backup Setting the Time Minutes and Seconds Time Display Your digital clock timer operates on a 12-hour cycle. The AM For a display of time in minutes and seconds: can be powered with a customer-installed 9-volt alkaline battery 1. Press and hold the WAKE SET/OFF button. This clock radio is equipped with a memory holding system that indicator on the left side of the display will light up to let you (not included). The power failure protection circuit will not know if the display is reading AM time. 2. While holding down WAKE SET/OFF button, momentarily operate unless battery is installed. 1. Slide the TIME SET/HI•LO Dimmer switch to TIME SET position press the SLEEP button. The hour digits will display minutes; and use the HOUR and MINUTE buttons to set the correct When normal household power is interrupted, or AC line cord is the minute digits will display seconds and start to increment. unplugged, the battery will power the clock radio to keep track Release the buttons to return to hour and minute display. RP-3701 am indicator time. of time and alarm settings programmed into memory. When on To indicate the AM time. 2. Slide the switch to HI or LO position to finish the time setting. battery power, the digital display will not light; however, should WAKE TIME occur during the power interruption, the radio will am/fm band switch Setting the Wake Time operate or the alarm will sound if remaining battery power is To select AM or FM band. Canadian Warranty adequate. Normal operation will resume after AC power is 1. Press and hold WAKE SET/OFF button. Wake time is displayed. Thomson Consumer ...