Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
Selecting AUX IN mode • Press AUX ON/OFF on the back of the unit to select AUX IN mode. • Press AUX ON/OFF again to exit from the AUX IN mode and resume to standby mode. To listen to the radio again, press . user manual manual de usuario EN/E It is important to read this user manual prior to using your new product for the fi rst time. Es importante leer este manual antes de usar por vez primera su equipo. RP5415 RP5415PK v5.0 (EN/E) PLEASE READ AND SAVE THIS FOR FUTURE REFERENCE IMPORTANT SAFETY INSTRUCTIONS Before you begin General controls Clock Sleep function Audiovox Electronics Corp. 150 Marcus Blvd, Hauppauge, NY 11788 ©2009 Audiovox Electronics Corp. Trademark(s) ® Registered Marque(s) ® Deposee(s) Marca(s) ® Registrada(s) Printed in China ] Plugging in for power AC OUTLET POWER SUPPLY: 120V~60Hz The AC power plug is polarized (one blade is wider than the other) and only fi ts into AC power outlets one way. If the plug will not go into the outlet completely, turn the plug over and try to insert it the other way. If it still does not fi t, contact a qualifi ed electrician to change the outlet, or use a different one. Do not attempt to bypass this safety feature. Power is fed to the unit even when it is not functioning. To cut the power supply off, the power cable must be unplugged. Front view Top view Radio If you set Sleep function with low volume level before going to bed, we advise using Wake to alarm mode. Battery back-up operation The power failure protection circuit will not operate unless battery is installed. When the battery backup functions, the digital display will not light, however, the wake function still occurs during the power interruption if remaining battery power is adequate. Normal operation will resume after AC power is restored so you will not have to reset the time or wake. Install battery as follow: 1. Remove battery compartment door (located at the bottom of the radio) by applying thumb pressure to the tab on battery door and then lift the door out and off the cabinet. 2. Connect a 9-volt battery (not supplied) to the connector plug. 3. Replace the compartment door. Power failure indicator When AC power is interrupted (disconnected) for a short period of time, both time and alarm settings will change (unless battery is installed). After AC power is restored (reconnected), the Digital Display will blink to indicate that power was interrupted and you should readjust the time and alarm settings. – turns on or off the radio; turns off the wake function SLEEP – activates sleep function SNOOZE – turns off the wake function temporarily; cancels the sleep function DISPLAY – switches between analog and digital clock displays Left view TUNING – selects radio frequency – Slide to activate Wake 1 settings and change Wake 1 mode: • (wake to alarm) – selects alarm as the waking mode • (wake to radio) – selects radio as the waking mode • OFF – deactivates Wake 1 waking mode WAKE 1 CHECK TIME – checks the waking time for Wake 1 AUX IN – jack for external audio input Right view + VOLUME – – adjusts volume – Slide to activate Wake 2 settings and change Wake 2 mode: • (wake to alarm) – selects alarm as the waking mode • (wake to radio) – selects radio as the waking mode • OFF – deactivates Wake 2 waking mode WAKE 2 CHECK TIME – checks the waking time for Wake 2 Back view BAND AM/FM – selects radio band AUX ON/OFF – selects auxiliary input mode – adjusts Wake 2 time – adjusts clock time – adjusts Wake 1 time – BRIGHTNESS + – adjusts display brightness Display brightness Clock time and radio frequency are displayed on the display area at the front of the unit. You can adjust the brightness of the display by rotating BRIGHTNESS on the back of the unit. Setting clock Turn the clock setting knob on the back of the unit to adjust clock time. The time decrements or increments will follow by a faster rate when you turn and hold the knob. The digital clock shows and a clock icon fl ashes on the display while you are adjusting the time. Selecting between analogue and digital clock Press DISPLAY to select between analogue and digital clock display. Switching on/off Press to turn on or off the radio. Switching band Slide the BAND AM/FM switch on the back of the unit to select FM or AM band. Tuning radio Turn the TUNING knob on the left of the unit to adjust radio frequency. Antennas AM Antenna – A built-in ferrite rod antenna eliminates the need for an outside antenna for AM reception. Rotating the unit slightly may improve reception of distant AM stations. FM Antenna – The power cord acts as your FM antenna. The power cord picks up moderate to strong stations and eliminates the need for an external antenna in most strong signal areas. Be sure the power cord is stretched out to its full length. Do not coil or bunch the cord together. Changing position of the power cord may improve reception. Built-In AFC – The Built In Automatic Frequency Control (AFC) works only on FM. It helps reduci...
Dieses Handbuch ist für folgende Modelle:Radios - RP5415PK (744.92 kb)