Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Whenusing the internal microphone/speaker or external microphone/headset (purchased separately), your voice or the signal is detected and the radio transmits and receives automatically. To turn off the VOX function, press the Function (F) button five times; then press the Up ( ) or Down ( ) button to turn the Vox function off. -12 VOX Sensitivity Level To set the VOX sensitivity level: 1. With the radio off, press the Function (F) button and, at the same time, press the Power button. 2. LE-03 (or 01-05), or dE-03 (or 01-05) will be displayed. If dE is displayed, press the Function (F) button and LE--- (level) will be displayed. 3. Press the Up or Down button to select from 1 to 5 voice sensitivity levels, with 1 being the most sensitive and 5 being the least sensitive. VOX Delay Adjustment To adjust the VOX delay: 1. Perform steps 1. through 3. above for VOX sensitivity level; then press the Function (F) button. 2. dE-03 (or 01-05) will be displayed. 3. Press the Up or Down button to select from 1 to 5 time delays, with 1 being the fastest and 5 being the slowest. 4. Press the Monitor (M) or PTT button to exit the VOX sensitivity/delay mode. Roger Beep Tone The unit will also transmit a beep tone sequence after each transmission to signal the receiving party that transmission has ended. This tone is called a “Roger Beep”. Press the press Function (F) button six times until the ( RGB ) icon flashes and “on” or “oF” appears. Then press Up ( ) or Down ( ) button to set the function on. The ( RGB ) icon will remain displayed. To disable the “Roger Beep”, proceed as before, until Beep Tone icon appears flashing. Then press Up ( ) or Down ( ) buttons to set the function to off. Press the PTT button to confirm your selection. Button Confirmation Tone Whenever the Up/Down or Function (F) select button is pressed, the speaker will sound a beep tone to confirm each press, provided the key tone feature is enabled. To disable the key tones, press Function button seven -13 times until the Beep Tone icon ( ) appears flashing and “on” or “oF” appears. Then press Up ( ) or Down ( ) to set the function off. Press the PTT button to confirm your selection. When “oF” is selected, no beep tones should be heard. To enable the key tones proceed as before, until Beep Tone icon appears flashing. The “On” icon will appear. Then press Up ( ) or Down ( ) button to set the function to on and the beep tones will be heard. Key Lock This feature prevents accidental change of unit settings. While enabled, Key Lock allows only the PTT button to operate. To enable Key Lock, press the Function (F) button for more than 2 seconds until Key Lock icon ( ) appears. To disable the Key Lock function, press the function button for more than 2 seconds until Key Lock icon disappears. To Transmit 1. Set the desired primary channel. 2. Press and hold the PTT (Push-to-Talk) button while speaking slowly and clearly in a normal voice, approximately 2 to 3 inches from the microphone. 3. The transmit lightning indicator ( ) will appear while transmitting. 4. Release the PTT (Push-to-Talk) button when you finish speaking to receive incoming signals. To Receive. 1. Set the desired channel. 2. Adjust the volume control to the desired listening volume by using the up and down buttons. 3. The transceiver will play strong received signals through its internal speaker or through a headset, if so equipped. 4. The receive lightning indicator ( ) will appear while transmitting. -14 Monitor Function The Monitor (M) button can be used to play all signals present on a channel. This is useful when communicating with other parties at extreme range. The monitor function can be locked on by pressing the Monitor (M) button for two seconds. When the monitor lock has been activated, the LCD display will indicate BUSY and the receive indicator lightning bolt appears. Pressing the monitor button a second time will unlock the monitor function. WARNING • Remove the batteries from the transceiver if it is not expected to be used for long periods. This will eliminate the possibility of battery acid leaking from the batteries and corroding the transceiver. • Avoid exposing the unit to water or extremes of temperature. • Do not use this device in or near a mining facility, which uses remotely triggered explosives or in areas labeled “Blasting Area”. Premature or accidental detonation may result. • Do not attempt to modify or in any way increase the output of this transceiver. Its output is designed to meet the legal limits set by the FCC. • Do not use this device or change its batteries in potentially explosive atmospheres as sparks in such areas could result in an explosion. • Turn your transceiver off wherever posted notices restrict the use of radios or cellular telephones. Facilities such as hospitals may use equipment that is sensitive to RF energy. • Turn your transceiver off on-board aircraft when requested to do so. • Do not place your transceiver in front of a vehicle’s air-bag...
Dieses Handbuch ist für folgende Modelle:Radios - FR-142B (87.81 kb)