Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Audiovox Dateigröße: 200.18 kb Dateiname: Unterrichtssprache:

128-6813 7 of 14 f. Insert the end of the ball strut into the keyed h. If the outside air temperature is cold, it may opening on the cradle mounting plate, and be beneficial to warm the adhesive backing secure the plate to the ball strut using the on the base using a portable hair dryer, or flatwasher, lockwasher and flat-head screw by holding the backing surface in front of a through the back of the plate. vehicle heater vent. g. Reattach the mounting plate assembly to the i. Remove the plastic liner from the adhesive rear or bottom of the cradle assembly, as backing on the base, and fix the base in desired, using the two flat-head screws position on the surface; make sure the removed previously. Installation of the mounting mounting pad is accurately positioned on base can now continue. the first try, since repositioning may be difficult, if not impossible. FLAT-HEAD SCREW CRADLE MOUNTING PLATE STAR NUT j. Bend the fins on the base so it conforms BALL STRUT to the mounting surface. If the mount is to be screwed in place, do not remove the plastic liner from the THREADED SOCKET adhesive backing. Use appropriate sheet MOUNTING BASE metal or machine screws for this purpose. -8 LOCKWASHER FLATWASHER 128-6813 8 of 14 NOTE: Allow a 72-hour period for the adhesive backing to cure completely. k. Using the star nut, attach the cradle assembly to the base threaded socket; do not overtighten the star nut. 3. Installing the Cradle Using Double-Sided Tape You can mount the cradle directly to your dashboard or other flat surface without using the cradle mount in the kit. To do this, do not remove either of the mounting plate assemblies from the cradle. a. Remove the 3/4” x 3” double-sided tape from the supplied kit. b. Determine the location of the cradle, and clean the mounting surface as before. c. Peel the backing from one side of the tape, and press the tape in place on the rear or bottom cradle mounting plate. d. Peel the backing from the exposed side of the tape and carefully position the cradle on the mounting surface, gently pressing the cradle into place. -9 4. Using Other Manufacturer’s Mounts The Shuttle Cradle can also be installed using other manufacturer’s mounts; the mounting plate provisions on the rear and bottom of the cradle provide you with multiple mounting options within the vehicle using various vehicle-specific aftermarket brackets, such as those purchased separately from Panavise, Pro-Fit, etc. 5. Installing the Shuttle into the Cradle The Shuttle cradle has three retaining clips---one on top and two on the bottom. Place the Shuttle in the cradle so that the Shuttle connectors are lined up; use the SAT and TERR RF connectors as guides. Then gently press in on the bottom of the Shuttle to engage the connectors. The top clip will automatically engage; then slide the two bottom clips back into the locked position. Cradle orientation can be adjusted by loosening the star nut and then tightening it when the cradle is in the desired viewing position. 128-6813 9 of 14 TOP RETAINING 16-PIN SYSTEM CLIPSAT. (MAIN) RF CONNECTORLEFT SLIDECONNECTOR TERR. RF CONNECTOR BOTTOM BOTTOM RIGHT CLIP SLIDE CLIP 6. Sirius Program Listening Options The Shuttle and Cradle provide an audio output signal in three manners: 1. When using CK1 or CK2 cradle, the audio signal can be routed through an audio cable which is applied to the auxiliary inputs of a radio or entertainment system. 2. When using the CK1 cradle, the audio signal can be transmitted to a car radio on one of four selectable FM frequencies. The audio signal can then be played through your car radio when the car radio is tuned to one of these frequencies. 3. Some listeners prefer to use a hard-wired FM transmitter. In this instance, when using the CK1 cradle, an optional FM Switching Box assembly (Part No. 112C3159) is available and provides a hard-wired FM output when connected to the FM OUT connector on the left side of the cradle; the other end of the switching box plugs into the antenna jack of your radio. By using this assembly, and selecting the appropriate FM output frequency (88.1MHz, 88.3MHz, 88.5MHz or 88.7MHz) with the slide switch, the Sirius signal received at the SAT (MAIN) or TERR. cradle antenna input can be played through your car radio when tuned to one of these frequencies. SHUTTLE CRADLE CK1 FM OUT AUDIO OUT DC 12V FM FREQUENCY SELECT SLIDE SWITCH: 88.1 MHz 88.3 MHz 88.5 MHz 88.7 MHz -10 128-6813 10 of 14 7. Mounting the Vehicle Antenna The antenna should be placed on a relatively flat surface on the vehicle exterior, preferably on the SHUTTLE roof (high point) or on the trunk (convertible). To (TYPICAL) mount the antenna: a. Plug the antenna into the SAT. (MAIN) connector on the back of the cradle. b. Place the antenna at the preferred location on the roof or trunk surface. If the vehicle is +12 VDC equipped with a roof or trunk rack, the antenna ADAPTER may have to be mounted off-center on the surface. The magnet will secure the antenna ...

Herunterladen

Geben Sie zwei Ziffern: