Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
If the Backup Battery has been installed and a power failure occurs or the AC cord is accidentally disconnected, the display backlight will not remain lit, but current time and alarm time settings will be temporarily maintained. Otherwise, you must reset the time and alarm settings. Note: The Battery Low Icon is located at the left side of clock display. When the backup battery is low and needs to be replaced, the icon will flash. REPLACING THE BATTERY 1. Please make sure the AC adaptor is connected. Otherwise all settings may be lost during battery replacement. 2. Place unit face down on a stable surface. Pull down and remove the backup battery compartment door located on the rear of the unit. 3. Insert a new CR2032 battery by easing it under the tabs in the battery well and pressing down. Make sure the side marked + is facing up. 4. Replace the battery compartment cover and stand unit back upright. Note: Make sure you dispose of battery properly (see your local regulations). WARNING: Lithium batteries can explode or cause burns if disassembled, shorted, recharged, exposed to water, fire, or high temperatures. Do not place loose batteries in a pocket, purse, or other container containing metal objects, mix with used or other battery types, or store with hazardous or combustible materials. Store in cool, dry, ventilated area. Follow applicable laws and regulations for transport and disposal. Setting Time Using iPhone/iPod Time Sync The iA63 Time Sync feature allows you to sync the time setting on the iA63 to the time from your docked iPhone or recent model iPod (iPod touch, iPod nano and iPod Classic; older iPod models such as iPod mini do not support this feature). 1. Dock your iPhone or iPod 2. Press and release the Time Set/ Sync Button located at the back of the unit. “SYNC” flashes on the display to indicate sync attempt. 3. Once sync is completed,the updated time will appear on the display and 2 beeps will confirm successful syncing. 4. If sync was not successful, “FAIL” will appear on the display and you will hear a long beep. If this happens, please try again, with a different iPhone or iPod if needed. If sync still fails, please see Setting Time Manually (page 6). NOTE: iPhone time is automatically updated to the correct time via cell phone towers. The time on your iPod is accurate only to the time on the computer the last time the iPod was synced to it. It’s possible to have up to 59 seconds difference between the iA63 and synced iPhone/iPod. Setting Up the iA63 Setting Up the iA63 Setting the Time manually 1. Slide the DST (Daylight Saving Time) Switch located on the back of the unit to +1 to add an hour (Spring) or to -1 to subtract an hour (Fall) to adjust for daylight saving time or standard time. 2. Press and hold the Time Set/Sync Button located at the back of the unit until the time flashes on the display and the unit beeps once. 3. Press the + or - Button to set the correct time (hold for faster setting). Remember to set the correct AM or PM time. The PM Indicator appears to the left of the time display; there is no AM indicator. 4. If desired, press the button during Time setting to toggle the clock display format to 12 hours or 24 hours. 5. When the correct time is displayed, press the Time Set Button again (or no button within 10 seconds) to exit the time setting mode. NOTE: You can also adjust settings on the iA63 via the iHome+Sleep app. To do so, press and hold the Button when the iHome+Sleep app is open and in view. See the iHome+Sleep Start Guide for more information. Using the Alarms iA63 lets you wake to FM radio, iPhone/iPod or buzzer alarm and to adjust the alarm volume. Setting the Alarms 1. Press and hold the Button until the alarm time flashes on the display then release. Press the + or - Button to set the alarm time (hold for faster setting). Remember to set the correct AM or PM time. 2. Press the Button again to confirm the set alarm time, then press the + or - Button to select an alarm source to wake to: iPod, Radio (the currently tuned radio frequency appears on the display) or Buzzer. For wake to iPod: select iPod to wake to a docked iPhone/iPod. If the unit does not detect an iPhone/iPod at the set alarm time, the iA63 will default to the buzzer alarm. The alarm cycle lasts for one hour; make sure you have enough music on your iPhone/iPod to last that long. For wake to radio: You can wake to a different preset station. After selecting Radio as the wake to source, press the Button as needed to cycle to the desired preset station (see Listening to Radio on page 8 for details on setting radio stations and presets). 3. Press the Button again, then press the + or - Button to set the alarm volume. 4. Press the Button again (or no button within 10 seconds) to exit the alarm setting mode. 2 beeps will confirm the alarm is set.The alarm is armed once set, indicated by the alarm icon on the display. Arming and Disarming Alarm (Turn Alarm Function On and Off) 1. Press the Button ...
Dieses Handbuch ist für folgende Modelle:Radios - IA63 (546.17 kb)