Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. RadioShack Customer Relations 300 RadioShack Circle, Fort Worth, TX 76102 12/99 Before You Begin Before you begin installation, read this manual and the separate Consumer Product Safety Commission information sheet. For your safety and convenience, plan each step of the installation and purchase the necessary hardware in advance. The hardware required and the order in which you perform the steps depend on the mounting and connection method you choose. Warning: When you install your antenna, use extreme caution. If the antenna starts to fall, let it go! It could contact overhead power lines. If the antenna touches the power line, any contact with the antenna, mast, cable, or guy wires can cause electrocution and death. Call the power company to remove the antenna. Do not attempt to remove it yourself. 1.-Inch Screws Large Wing Nuts Crossover Wires Threaded posts Splint Flat Washers Large Wing Nuts U-Bolt Main Boom Backup Plate Lock Nuts Mast Clamp Step 1: Assemble the Antenna Metal Support Straps Main Boom Cradle Boom Mast Clamp Assemblies Metal Support Straps UHF Bowtie Lead-In Terminal UHF/VHF Isolation Network Step 2: Connect Coaxial Cable to the Antenna Lead-In Terminal Spade Terminal Strain Relief Tab Matching Transformer F-Connector Main Boom Spade Terminal Large Wing Nuts Flat Weather Washers Boot Lead-In Terminal ©2008. RadioShack Corporation. All rights reserved. RadioShack and RadioShack.com are trademarks used by RadioShack Corporation. 10A08 15-2156 Printed in the USA Step 6: Connect to your Audio/Video System Connect the antenna’s coaxial cable to your audio/video system’s antenna terminals according to the type of connections you have. RadioShack carries a variety of splitters and other accessories; choose one that best suits your needs. Below are some sample connections. If you have: • Twin-lead UHF terminals • Coaxial VHF terminal • Twin-lead FM antenna terminals Use a RadioShack Splitter with 75-Ohm Input To FM Receiver From Antenna UHF 300 Ohm VHF 75 Ohm If you have: • Twin-lead UHF terminals • Twin-lead VHF terminals • Twin-lead FM antenna terminals Use a RadioShack Transformer/Splitter To FM Receiver From Antenna UHF 300 Ohm VHF 300 Ohm If you have: • Combined coaxial VHF/UHF terminal • Coaxial FM antenna terminal Use a RadioShack VHF/UHF Splitter/Combiner From Antenna TV VHF/UHF To FM Receiver If you want to: • Use the antenna in combination with a cable or satellite set-top-box, and • Your TV has a coaxial (antenna in) terminal. Use a RadioShack High Isolation A/B Switch. A IN TV OUT B IN From set-top-box From Antenna To TV If you want to: • Use the antenna in combination with a cable or satellite set-top-box, and • Your TV has both a coaxial (antenna in) terminal and A/V terminals (usually red/yellow/white). Use a RadioShack Gold A/V cable. VIDEO IN AUDIO IN CABLE/ANT. IN LEFT RIGHT ANTENNA IN TV OUT VIDEO L R CH3 CH4 Set-top-box TV From Antenna A/V Cable RadioShack also carries these and many other antenna mounting accessories: Grounding Block Antenna Mast Tripod Mount Antenna Rotator Outdoor Coaxial Cable Step 3: Unfold the Antenna’s Elements 1. Hold the main boom’s elements near the pivot points and pull them away from the boom until they snap into the self locking plastic support insulators. Caution: To avoid damage to the elements, do not pull them near their outer ends. Once the elements are locked into position, do not attempt to unlock them. Doing so might break the self-locking tabs. 2. Hold each wing boom and turn its elements until they snap squarely into place perpendicular to the boom. 3. Press the supplied small end plugs into the wing booms. 4. Bolt the triangular wing boom brackets onto the main boom using the supplied 1.-inch screw and small wing nut, as shown. 5. Insert the top and bottom wing booms into the wing boom brackets. Secure them with the four supplied 1.- inch screws and small wing nuts, as shown. Step 4: Attach Antenna to the Mast We recommend that you enlist the help of another person before you put up the mast or attach your antenna to it. How you set up your mast depends on your specific installation. Refer to the separate Consumer Product Safety Commission information sheet for recommended methods. 1. Slide the antenna’s mast clamp assemblies over the end of the mast. 2. Tighten the mast clamp assemblies’ lock nuts to hold the antenna in place. Do not overtighten the lock nuts. Caution: The crossover wires must not touch the antenna boom, the mast, or each other. If necessary, carefully bend the crossover wires to provide at least .-inch of clearance between parts. 3. Set up the mast, then rotate it so the antenna’s shorter elements point toward the broadcast antennas of the stations you want to receive. Step 5: Route Cable to Your Audio/Video System • Use plastic tape or mast standoff insulators to secure the coaxial cab...