Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
12-1632 OWNER’S MANUAL Please read before using this equipment. AM/FM PLL Clock/Table Radio 12-1632.fm Page 2 Wednesday, May 10, 2000 10:57 AM FEATURES Your RadioShack AM/FM PLL (Phase Locked Loop) Clock/Table Radio offers you all the features of an alarm clock and an AM/FM radio in one convenient package. You can wake to a buzzer or your favorite AM or FM radio station. You can also fall asleep with the radio playing, and the radio automatically shuts off at a preset time. The clock radio’s features include: PLL Digital Tuning — digital phase locked loop synthesizer provides drift-free frequency tuning with the highest degree of accuracy and stability. 20 Station Memory — lets you store ten AM stations and ten FM stations into memory for easy recall. Liquid Crystal Display with Brightness Control — makes the clock easy to read, even in low light situations. 21/4" Speaker — for quality broadcast sound. Battery Backup with Battery Sentinel® — maintains clock and alarm operation during a power failure and lets you know when to install a new battery. Vertical, Space-Saving Design — lets you save space on your night stand or table. Sleep Timer — lets you set the radio to play for up to 90 minutes then automatically turn off. Snooze — lets you repeatedly silence the alarm for about 5 minutes or cancel the sleep timer feature. WARNING: To reduce the risk of fire or shock hazard, do not expose this product to rain or moisture. CAUTION !RISK OF ELECTRIC SHOCK. DO NOT OPEN. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER OR BACK. NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. This symbol is intended to alert you to the presence of uninsulated dangerous voltage within the product’s enclosure that might be of sufficient magnitude to constitute a risk of electric shock. Do not open the product’s case. ! This symbol is intended to inform you that important operating and maintenance instructions are included in the literature accompanying this product. The graphical symbols with supplemental markings are located on the back of the case. © 1999 Tandy Corporation. All Rights Reserved. RadioShack and Battery Sentinel are registered trademarks used by Tandy Corporation. 2 12-1632.fm Page 3 Wednesday, May 10, 2000 10:57 AM PREPARATION CONNECTING TO AC POWER Plug the clock radio’s power cord into a standard AC outlet. The display turns on and the BATTERY SENTINEL indicator lights. (See “Installing Back-Up Batteries.”) Caution: The clock radio’s AC power cord is equipped with a polarized plug to prevent electric shock. One blade on the cord’s plug is wider than the other and the plug only fits an outlet one way. If you cannot easily insert the plug, turn it over and try again. Do not force it. INSTALLING BACK-UP BATTERIES To keep the clock running for up to 8 hours during an AC power failure, install three AA batteries (not supplied) in the battery compartment. For the longest life, we recommend alkaline batteries. Caution: Use only fresh batteries of the required size and recommended type. Note: To prevent unnecessary drain on the battery, connect AC power then install the batteries. Follow these steps to install back-up batteries. 1. Slide the battery compartment cover in the direction of the arrow and remove it. 2. Place the batteries in the compartment and on top of the attached ribbon, as indicated by the polarity symbols (+ and –) marked in the compartment. 3. Replace the cover. The BATTERY SENTINEL indicator lights if the back-up batteries are not installed or need to be replaced. Warning: Always dispose of old batteries promptly and properly. Do not bury or burn them. 3 12-1632.fm Page 4 Wednesday, May 10, 2000 10:57 AM A QUICK LOOK AT THE CONTROLS MEMSLEEP Radio/Alarm Selector Operation Selectors Station Mem- ory Selectors SNOOZE Bar Display Brightness Switch Time Setting Indicator Alarm Indicator AM/PM Indicator Alarm Setting Indicator Battery Sentinel Indicator Radio Station Tuning Bar/ Hour-Minute Setting Bar Sleep Timer Indicator Station Memory Indicator 4 12-1632.fm Page 5 Wednesday, May 10, 2000 10:57 AM OPERATION SETTING THE TIME 1. Press MODE. The time and appear. 2. Hold down MEMORY/TIME then repeatedly press (or hold down) 6 9999 HOUR until the display shows the correct hour setting. Note: PMappears when you set a PM hour. AMappears for an AM hour. 3. Hold down MEMORY/TIME then repeatedly press (or hold down) MIN 5 8888until the display shows the correct minute setting. CHANGING THE DISPLAY BRIGHTNESS To change the brightness of the display, set DIM HI/LO to HI or LO. SETTING THE ALARM TIME 1. Repeatedly press MODE until SET ONand the current alarm time appear. Note: If you do not set the alarm time within 10 seconds, the clock radio displays the previous function. To continue, start over at Step 1. 2. Hold down MEMORY/TIME then repeatedly press (or hold down) 6 9999 HOUR until the display shows the desired alarm hour setting. 3. Hold down MEMORY/TIME then repeated...