Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
position the radio face down. 2. Press the catch and slide in the direction of the arrow. 3. Lift up the battery cover. 4. Insert 2xUM-3 (AA) size batteries. Make sure the batteries are positioned in accordance with the diagram indicated. 5. Replace the battery cover. Battery replacement The battery indicator will appear and flash in the display when the batteries are in need of replacement. After removing the batteries, you have approximately 3 minutes to replace the batteries after which clock and memory information will be lost. Setting the clock time The clock will start running when the batteries are installed. When the batteries are installed for the first time, the display will show 0:00. Note: Time can only be set with the radio switched off. 1. Ensure that the radio is switched off. 2. Press and hold down the Time Set button for more than 2 seconds until the hours digit begins to flash in the display. 3. Whilst the hours digit is flashing, adjust the hours using Tuning Up/Down buttons. 4. Press the Time Set button, the minute digit begins to flash in the display. 5. Whilst the minute digit is flashing, adjust the minutes using the Tuning Up/Down buttons. 6. Press the Time Set button to complete time setting. Setting the alarm time 1. Ensure that the radio is switched off. 2. Press and hold down the Alarm button for more than 2 seconds until the hours digit and alarm symbol begin to flash in the display. 3. Whilst the hours digit is flashing, adjust the hours using the Tuning Up/Down buttons. 4. Press the Alarm button, the minute digit begins to flash in the display. 5. Whilst the minute digit is flashing, adjust the minutes using the Tuning Up/Down button. 6. Press the Alarm button to complete alarm time setting. The Alarm symbol will appear on the display indicating the alarm is set. Wake to alarm 1. At the pre-selected time, the alarm will beep. The alarm may be turned off for 24 hours by pressing any button. The alarm will switch off automatically after 3 minutes. 2. To permanently cancel the alarm, press the alarm button, the alarm symbol will be removed from the display. GB Operating the radio-search tuning 1. Switch on your radio by pressing the Power Button. Note: The radio is originally set to be 90 minutes auto shut off after Power is switched on ( symbol will appear on the display). If you don’t need this feature, press Power button for more than 2 seconds until symbol removed from the display. 2. Select the required waveband by repeatedly pressing the Band button. On FM bands, fully extend the Telescopic aerial. On AM (MW) band, rotate your radio for best reception. 3. Press and hold down either the Tuning Up or Down buttons until frequency in the display begins to change rapidly. Release the button. 4. Your radio will scan the selected waveband, stopping each time if finds a station of sufficient strength. Adjust the volume control to the required level. Operating the radio – manual tuning 1. Switch on your radio by pressing the Power button. 2. Select the desired waveband using the Band button. The waveband selected will appear in the display. On FM bands, fully extend the Telescopic aerial. On AM (MW), rotate your radio for best reception. 3. A single press on either the Tuning Up/Down will change the frequency up or down. Adjust the Volume control to the required level. AM(MW) tuning step In Europe and other parts of the world AM (MW) tuning steps are 9 kHz, in America the AM tuning step is 10 kHz. To change the AM tuning step from 10 kHz to 9 kHz, proceed as follows, 1. Switch on your radio and select the AM(MW) waveband. 2. Switch off the radio. 3. Press Tuning Down then Power button, the radio will be changed into 9 kHz tuning step on AM band. To change the AM tuning step from 9 kHz to 10 kHz, proceed as follows, 1. Switch on your radio and select the AM(MW) waveband. GB 2. Switch off the radio. 3. Press Tuning UP then Power button, the radio will be changed into 10 kHz tuning step on AM band. Presetting stations You may store up to 10 stations each on FM, AM (MW) bands giving a total of 20 preset stations. 1. Tune into the required stations using one of the tuning methods previously described. 2. To store the station, press and hold down one of the PRESET button 1-5 for more than 2 seconds until display shows preset location. 3. To store the station into preset 6-10, press +5 button, display will show +5, then press and hold down one of the PRESET button 1-5 for more than 2 seconds until display shows preset location. Recalling a preset station 1. Switch on your radio using the Power button. 2. Select the desired waveband using the Band button. 3. Simply press one of Preset buttons 1-5 to recall the required preset stations. To recall preset stations 6-10, press +5 button, then the Preset button 1-5. Display modes Whilst radio is switched on, press Display button to change between frequency and normal time. Display backlight Pressing the Light button will switch on the display ba...