Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Emerson
Dateigröße: 772.41 kb
Dateiname: d9840f0d-7b6e-bb84-7d90-751a5ef8899c.pdf
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
POWER SOURCE This radio is designed to operate on normal 110V-120V 60Hz AC power only. Do not attempt to operate the radio on any other power source. You could cause damage to the radio that is not covered by your warranty. This radio should be connected to an AC outlet that is always ‘live’. Do not connect it to an outlet that is controlled by a wall switch. When the power to the radio is interrupted, the Sure Alarm battery back up system takes over to maintain the time and alarm settings. To maximize the life of the back up battery, keep the radio connected to a ‘live’ AC outlet at all times. This radio uses a polarized AC plug which has 9VOLT Press one blade wider than the other. This plug will only fit into a polarized AC outlet. This is a safety feature. If the plug will not fit, you may have an older non-polarized AC outlet. Do not defeat the safety feature by trying to file the wider blade, or replacing the plug. Contact an electrician to replace your outdated outlet. 4 Top Panel 1. Sleep On switch (sleep to music timer). 2. Alarm 1 setting button. (Alarm 1/2 Reset) 3. Fast Reverse button. 4. Slow Reverse button. 5. Clock setting button. 6. Slow Forward button. 7. Fast Forward button. 8. Alarm 2 setting button.. 9. Radio ‘On’ button. 10. Snooze (Sleep ‘Off’ / Radio ‘Off’) button. Left Side 11. Display Dimmer switch (HIGH/LOW). 12. Alarm 2 selector switch (OFF/RAD/BUZ). 13. Alarm 1 selector switch (OFF/RAD/BUZ). LOCATION OF CONTROLS AND INDICATORS 111112:382:382:382:382:38 Right Side 14. Tuning control. 15. Band switch (AM/FM). 16. Volume control. Front Panel 17. AM indicator. 18. Alarm 1 ‘On’ indicator. 19. Time display. 20. Alarm 2 ‘On’ indicator. 21. Tuning Dial. 22. Lighted Dial Pointer. Bottom Panel 23. Back up battery compartment. 24. AC power cord. 5 OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS SETTING THE CLOCK When you connect the radio to your AC outlet for the first time the clock display will begin flashing “12:00” (AM). The flashing will stop when you set the time. AM indicator ALM 1(ALARM 1) indicator ALM 2(ALARM 2) indicator 1. Depress the Clock button and either the Fast Forward or Fast Reverse buttons to rapidly move the time display forward or back. 2. As the display approaches the correct time release fast setting buttons and depress the Slow Forward or Slow Reverse buttons until the correct time appears, then release all buttons. Note: Be sure to observe the AM indicator to make sure that the time is set correctly for AM or PM. If the AM indicator is ‘on’, the time displayed is “AM”. If the AM indicator is ‘off’, the time displayed is “PM”. SETTING THE WAKE UP TIMES This clock radio has two separate alarms that can be set and used independently. You may use the alarms to wake two people at different times, or you may use one alarm for weekdays and the other for weekend wake up times. The procedure for adjusting the wake up time is the same for both Alarm 1 and Alarm 2. 1. Depress and hold either the Alarm 1 or Alarm 2 setting button. The display will change from the correct time to the Alarm 1 or Alarm 2 wake up time. 2. While holding the Alarm 1 or Alarm 2 setting button, depress either the Fast Forward or Fast Reverse button to move the display rapidly ahead or back. 3. As the display approaches your desired wake up time, release fast setting buttons and depress the Slow Forward or Slow Reverse buttons until the desired wake up time appears, then release all buttons. Note: Be sure that you have set the wake up time correctly by observing the AM indicator. If the AM indicator is ‘on’ the wake up time is “AM”. If the AM indicator is ‘off’, the wake up time is “PM”. 6 CHECKING THE WAKE UP TIMES Whenever you want to check the wake up times, simply press either the Alarm 1 or Alarm 2 setting buttons. The display will change from correct time to wake up time. Release the Alarm 1 or Alarm 2 setting buttons to return to correct time. LISTENING TO THE RADIO 1. Set the Band selector to the desired band, AM or FM. 2. Set the Volume control to a low setting. 3. Press the Radio On button to turn the radio ‘On’. The radio dial pointer will light. 4. Select your desired station with the Tuning control. 5. Adjust the Volume control to the desired setting. 6. When you are finished listening, press the Snooze/Radio Off button to turn the radio ‘Off’. The radio dial pointer light goes off. ANTENNA INFORMATION AM – The AM bar antenna is inside the cabinet. If AM reception is weak, change the position of cabinet until the internal antenna picks up the strongest signal. FM – The FM antenna is built in to the AC power cord. If FM reception is weak try varying the position and direction of the power cord until you find the strongest signal. WAKE TO RADIO 1. Turn the radio ‘On’ and select the band, station, and volume level that you wish to hear when the alarm comes on, then turn the radio ‘Off’ again. 2. Reconfirm the wake up time settings for the alarm you are using, Alarm 1, Alarm 2, or both alarms. ...