Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Even if you are going to use the unit from the mains, we advise you to inser t the non-rechargeable batteries. This guarantees automatic back-up in case of mains failure. EngliSh Mains operation 1 Put the appliance plug in the parent unit and put the adapter into a wall socket. The power-on light goes on. Operation on non-rechargeable batteries The parent unit runs on four 1.5V R6 AA batteries (not included). We strongly advise you to use Philips LR6 PowerLife batteries. Do not use rechargeable batteries, as the parent unit does not have a charging function. Unplug the parent unit and make sure your hands and the unit are dry when you insert the non- rechargeable batteries. 1 Turn the locking knob a quarter turn (1) and slide the battery cover downwards to remove it ( ) (Fig. ). Insert four non-rechargeable batteries. Make sure the + and - poles of the batteries point in the right direction. Replace the battery compartment lid. Note:When the batteries are low, the power light on the parent unit flashes red. Note:When the batteries are completely empty, the parent unit automatically switches off and loses contact with the baby unit. using the appliance 1 Place the two units in the same room to test the connection (Fig. 5). Make sure the baby unit is at least 1 metre/3 feet away from the parent unit. Press the on/off button to switch on the baby unit (Fig. 6). The power-on light lights up green continuously. Turn the volume control to switch on the parent unit and to set the volume to the level you prefer. (Fig. 7) The power-on light lights up green continuously. When a connection has been established between the units, the connection light on the , parent unit lights up green constantly. Note: It takes about 30 seconds before a connection is established. Note: If a connection cannot be established, the connection light on the parent unit flashes red. 5 Place the baby unit at least 1 metre/ feet away from your baby (Fig. 8). Place the parent unit within the operating range of the baby unit. Make sure it is at least 1 metre/ feet away from the baby unit. For more information on the operating range, see section ‘Operating range’ below (Fig. 9). Operating range The operating range of the baby monitor is 200 metres/600 feet in open air. Depending on the surroundings and other disturbing factors, this range may be smaller. Dry materials Material thickness Loss of range Wood, plaster, plaster cardboard, glass <30cm/12in 0-10% (without metal, wires or lead) Brick, plywood <30cm/12in 5-35% EngliSh Dry materials Material thickness Loss of range Reinforced concrete <30cm/12in 30-100% <1cm/0.4in Metal grilles or bars 90-100% Metal or aluminium sheets <1cm/0.4in 100% For wet and moist materials, the range loss may be up to 100%. Features Digital signal confirmation The parent unit has a link light that continuously advises you of the status of the connection between the baby and the parent units.You can set an aler t on the parent unit to notify you if the link is lost.The aler t will sound an audible beep and the link light will flash red when a connection is lost. to activate the alert on the parent unit: 1 Turn the locking knob a quarter turn (1) and slide the battery cover downwards to remove it ( ) (Fig. ). Set the link alarm switch in the battery compartment to the ‘on’ position. Replace the battery compartment lid. To switch off the aler t, set the link aler t switch to the ‘off ’ position. adjustable sound sensitivity With the microphone sensitivity control on the baby unit, you can set the sound that is picked up by the baby unit to the desired level: low, mid or high. When the microphone sensitivity is set to ‘high’, the baby unit picks up all sounds. Note:The sensitivity of the baby unit can only be changed when there is a connection between the baby unit and the parent unit. 1 Use the microphone sensitivity control to set the microphone sensitivity of the baby unit to the desired level.You can use your own voice as a sound reference (Fig. 10). The power-on light on the baby unit turns yellow when a sound is transmitted. Note:Whilst operating on batteries, if the sensitivity is set to a high level, the parent unit will consume more power. adjustable loudspeaker volume You can change the volume on the parent unit, so you can adjust to suit your surroundings. 1 Turn the volume dial on the right side of the parent unit until the desired loudspeaker volume for the parent unit has been reached. Note:Whilst operating on batteries, if the volume is set to a high level, the parent unit will consume more power. Channel selector Always make sure that the channel selectors inside the batter y compar tments of both units are set to the same channel. With these channel selectors, you can select sixteen different channel positions. If you experience interference from other baby monitors, radio devices etc., select a different channel.. Open the battery compartment lids of both units. 10 EngliSh Baby unit: (Fig. ) , -Turn th...