Stimmen - 4, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
Babysense can alert when these signs indicate a cold, high fever, or other illness. In the extreme, breathing cessation can be related to Crib Death (S.I.D.S: Sudden Infant Death Syndrome) still a number one cause of death in infants up to one year of age. The syndrome is impossible to predict and modern medicine has not yet come up with means of cure or solution, thereby "Babysense II" is limited as a safeguard. However, it is a unique safety system which has helped save infants, giving parents (or caretaker) assurance, by enabling intervention in the event of irregular beathing movement or distress, before it becomes critical. There are a number of cautionary steps which are internationally recommended for SAFE SLEEPING: * Always lay baby to sleep on back. * Refrain from smoking near or around baby. ‘Avoid over-heating of baby's surrounding. Babysense is an addition to these precautions. “Babysense II” is a home movement monitor for basically healthy infants, excluding high-risk infants requiring constant medical supervision. Main Features “Babysense II” continually detects baby’s motion and breathing movements, and will set off a sound and visual alarm if movement stops for 20 seconds or if the breathing rate slows to below 10 breaths per minute. The system’s non-touch sensor pads under the mattress monitor baby’s movement without restraining him. Installation 1. Place the two sensor pads on the bottom of the bed (see illustration 1), or one sensor pad (see note below on newborns). Place mattress firmly on top of sensor pads. If the mattress cannot be in contact with the sensor pads, or if the mattress is on springs, it will be necessary to place a wooden board on the bed base on which to place the sensor pads, and then the mattress on top. 2. Remove battery cover (see illustration 3), remove battery housing and insert, in accordance with the markings, 4 new and identical size AA 1.5 volt batteries, preferably alkaline. Replace battery housing and close cover. 3. Attach cords of the two sensor pads to the doubleconnector of the connecting cable. Attach end of connecting cable to the outlet marked "SENSOR-IN" on the control unit. When using a single sensor pad, attach cord directly to the "SENSOR-IN" outlet without using the connecting cable. IMPORTANT: To avoid possible danger from dangling sensor cords, it is recommended to collect excess cord length with the included tie, or wrap excess cord length carefully around bed posts, as shown in illustration 1. 4. Press hanging hook firmly into slot in back of control unit (see illustration 3), and hang from the edge of the bed, or anywhere out of baby's reach. Note on installation for newborns (until beginning to crawl) When using for infant not yet able to crawl, use only one sensor pad - without the connecting cable. This will ensure greater relative sensitivity. When baby begins to move around, moving onto area not"covered" by the sensor pad, the second pad must be attached, using the connecting cable. Contents Monitoring Control Unit, hanging hook, 2 sensor pads and connecting cable Operation See illustration 2 for layout of control unit featuring: • On/off button under protective cover • Motion-activated green light • Red alarm light, activate if baby's breathing stops or slows significantly. • Low battery warning light To operate, press on/off button. When switched on, the control lights switch on briefly and a click will be heard. When breathing and movement are sensed, the green light flashes. If red low-battery warning light flashes (see illustration 2), replace batteries as soon as possible. If in addition clicking is heard, batteries must be replaced immediately. Turn off by pressing on/off button. Twin connector fll V Two sensor inputs » Connenctina | receptacle blocked -1 1- Fig. 3 Fig. 2 Features • Powered by size AA 1.5 volt batteries. Power consumption approx. 1 mA. • Battery life approx 6 months using alkaline batteries. • Alarm volume typically 85dB SPL at distance of one meter. • Illumination typically 2 mCD. WARNING Babysense is a high quality, high sensitivity electronic device which must be handled with care: • Do not handle roughly, drop or throw it. • Follow the installation instructions carefully to ensure that it is installed securely and correctly. • Babysense is not a toy: Do not allow children of any age to play with it. Testing Operation "Babysense II" is an exceedingly sensitive device which monitors baby's breathing movements through the mattress during sleep. There are two main malfunction causes - technical malfunctions and malfunctions due to environmental causes: Technical malfunction: In order to minimize technical problems, follow installation and operation instructions carefully. Environmentally caused malfunction: Due to the extreme sensitivity of "Babysense II", it can be influenced by fans, wind, air conditioning, and so forth. Such environmental effects could be picked...