Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
• Pu (PUSH): After pushing the [SQL] for 1 sec., and emits audio while pushing and holding • Ho (HOLD): After pushing the [SQL] for 1 sec., the squelch and emits audio even [SQL] is released. To close the squelch, push any key. PUSH Monitor action PUSH Monitor action Hold (default) D Automatic backlighting “ bL” This function is convenient for nighttime operation. The automatic backlighting can be adjusted from OFF, 1 (dark) – 3 (bright); 3 (default). Select 1– 3 to turn this function ON. • The automatic backlighting turns the backlighting ON when any key except for [PTT] is pushed. • The backlighting is automatically turned OFF after 5 sec. of inactivity. PUSH Automatic backlighting Automatic backlighting (default) OFF 8 SET MODE D LCD contrast selection “ LC” The contrast of the LCD • 1 (bright) – 4 (dark); 3 (default) PUSH LCD contrast 3 (default) LCD contrast 1 D Auto power save function “ PS” The auto power save function reduces current drain the receiver circuit for preset intervals. PUSH Auto power save ON Auto power save OFF (default) D Self check function “ SC” The self check function and informs you in case The following items are checked after switches to operation mode. • Temperature : Outside of – 35° C to +73° C; – 31° F to +163° F (approx.) • Connected battery voltage • Water intrusion PUSH Self check OFF (default) Self check ON When error messages as shown below are displayed, see trouble shooting for advice (p. 28). Temperature error Battery voltage error Water intrusion error D Battery voltage “ bt” This function contains voltage of the connected • The voltage of the connected battery after power is turned ON. PUSH Battery voltage OFF Battery voltage ON (default) D Scrambler code “ cd” (Available for I/S version only) There are 32 codes (1 to 32) available for programming. In order to understand each other, all transceivers in your group must have the same scramble code. PUSH Scrambler code 1 (default) Scrambler code 32 SET MODE 8 SET MODE LIST Function Indication Switch Beep tone function "bP" OFF / ON* / US Weather alert function "AL" OFF* / ON Priority scan function "Pr" OFF* / ON Scan resume timer "St" OFF* / ON Auto scan function "AS" OFF* / ON Dual/Tri-watch function "dt" Dual* / Tri Monitor switch action "Sq" Push* / Hold Automatic backlighting "bL" OFF / 1 / 2 / 3* LCD contrast selection "LC" 1 / 2 / 3* / 4 Auto power save function "PS" OFF / ON* Self check function "SC" OFF* / ON Battery voltage indicator "bt" OFF* / ON Scrambler code** "cd" 1* / 2 / / 32 * default setting ** Available for I/S version only 9 BATTERY CHARGING Battery charging Prior to using the transceiver pack must be fully charged CAUTION: To avoid damage to the transceiver, turn it OFF while charging. • Recommended temperature range for charging: +10° C to +40° C (+50° F to +104° F) - The Li-Ion battery is functioning within – 20° C to +60° C (–4° F to +140° F) • Use the specified chargers (BC-119N, BC-121N and BC152). NEVER use another manufacturer’s charger. • Use the supplied AC adapter (BC-147A/E) for BC-152. NEVER use another manufacturer’s AC adapter. Recommendation: Charge the supplied battery pack for a maximum of up to 10 hours. Li-Ion batteries are different from Ni-Cd batteries in that it is not necessary to completely charge and discharge them to prolong the battery life. Therefore, charging the battery in intervals, and not for extended periods is recommended. Cautions NEVER incinerate used battery packs. may cause an explosion. NEVER immerse the battery pack in water. If the battery pack becomes wet, be sure to wipe it dry the battery terminals) BEFORE attaching Otherwise, the terminals will become corroded, failure, etc. NEVER short the terminals of the battery pack. Also, current may flow into nearby metal objects, such as a necklace, etc. Therefore, be careful when carrying with, or placing near metal objects, carrying in handbags, etc. AVOID leaving the battery pack in a fully charged, or completely discharged condition for long time. It causes shorter battery life. In case of leaving the battery pack unused for a long time, it must be kept safely after discharge, or use the battery until the battery indicator shows the middle level, then remove it from the transceiver. If your battery pack seems to have no capacity even after being charged, completely discharge it by leaving the power ON overnight. Then, fully charge the battery pack again. If the battery pack still does not retain a charge (or very little), a new battery pack must be purchased. BATTERY CHARGING 9 i Charging connections q Attach the BC-152 to a flat surface, such as desk • For your convenience: etc., if desired. w Connect the AC adapter (BC-147A/E) as e Insert the battery pack with/without charger. • The charge indicator lights green. r Charge the battery pack approx. 9– 10 hours, depending on the remaining power condition. Eyelet: AC adapter BC-152 BP-227 IC-M88 Supplied screws Ensure sides of the battery pack are correctly...