Stimmen - 2, Durchschnittliche Bewertung: 3 ( )

Hersteller: Kenwood Dateigröße: 375.24 kb Dateiname: Unterrichtssprache:

3% distortion) Duty Cycle Transmit: 20% 13W (@ 4 . 5% distortion) Internal: 3.2W (@ 16 . 3% distortion) Operating Temperature Range -22.F ~ +140.F (-30.C ~ +60.C) 3.5W (@ 16 . 5% distortion) Frequency Stability ±0.00025% (-22.F ~ +140.F) TRANSMITTER (Measurements made per EIA/TIA-603) Antenna Impedance 50 . RF Output Power 50 to 15 watts 45 to 15 watts High: 50 watts 45 watts Dimensions (W x H x D) 7-1/12” x 2” x 7” Low: 15 watts 15 watts (180mm x 50mm x 170mm) Type of Emission Weight (net) 5.9 lbs (2.7kg) Wide: 16K0F3E, 20K0F1D FCC ID ALH32273110 ALH32283110 Narrow: 11K0F3E, 11K2F1D Band Spread 38MHz 50MHz Spurious Response 75dB * During simultaneous operation of conventional and LTR® modes. Conventional channel/trunking ID can be programmed up to 512. FleetSync® is a trademark of Kenwood Corporation. LTR® is a registered trademark of Transcrypt International. Applicable MIL-STD & IP FM Hum & Noise Wide: 48dB Narrow: 42dB Microphone Impedance 600 . Audio Distortion Less than 1% at 1000Hz Kenwood follows a policy of continuous advancement in development. For this reason specifications may be changed without notice. Standard MIL 810C Methods/Procedures MIL 810D Methods/Procedures MIL 810E Methods/Procedures MIL 810F Methods/Procedures footnotes from Front: 1 KRK-9, KCT-22M/M2/M3, KCT-23M/M3 remote control options required. Low Pressure 500.1/Procedure I 500.2/Procedure I, II 500.3/Procedure I, II 500.4/Procedure I, II 2 6-Pin Accessory Connector for external High Temperature Low Temperature 501.1/Procedure I, II 502.1/Procedure I 501.2/Procedure I, II Cat. A1 502.2/Procedure I, II Cat. C1 501.3/Procedure I, II Cat. A1 502.3/Procedure I, II Cat. C1 501.4/Procedure I, II 502.4/Procedure I, II speaker, PA Output & ignition sense input. 3 KCT-18 ignition sense cable option required; plugs into mobile 6-pin jack ignition sense input. Temperature Shock Solar Radiation 503.1/Procedure I 505.1/Procedure I 503.2/Procedure I Cat. A1, C1 505.2/Procedure I 503.3/Procedure I Cat. A1, C1 505.3/Procedure I 503.4/Procedure I, II 505.4/Procedure I 4 Built-in PA/HA outputs (no option board required); Horn Alert operates for 2-Tone or DTMF selective call decode only. Rain Humidity 506.1/Procedure II 507.1/Procedure II 506.2/Procedure II 507.2/Procedure II 506.3/Procedure II 507.3/Procedure II 506.4/Procedure III 507.4 5 Short Text Messages are radio stored & LCD displayed; Long Text Messages require a KDS-100 and KCT-40. Salt Fog 509.1/Procedure I 509.2/Procedure I 509.3/Procedure I 509.4 6 FleetSync® GPS features require an internal Dust Vibration 510.1/Procedure I 514.2/Procedure VIII, X 510.2/Procedure I 514.3/Procedure I Cat. 8 510.3/Procedure I 514.4/Procedure I Cat. 8 510.4/Procedure I, III 514.5/Procedure I Cat. 20 GPS board or externally wired GPS receiver with NMEA TTL level serial data output to the internal COM 1 or 2 set to "GPS". Shock 516.2/Procedure I, II, III, V 516.3/Procedure I, IV, V 516.4/Procedure I, IV, V 516.5/Procedure I, IV, V JQA-QMA1205 AD...

Herunterladen

Geben Sie zwei Ziffern: