Login:
Stimmen - 4, Durchschnittliche Bewertung: 4.5 ( )

Anleitung Binatone, modell TERRAIN 650

Hersteller: Binatone
Dateigröße: 1.08 mb
Dateiname: terrain-650-manual-btp-_090305_v2.0.pdf
Unterrichtssprache:en
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


PWR(POWER) Button – Press CALL button and hold to turn -Press to send the unit ON or Ringing tone to OFF. other PMR units. MENU Button -Press to change To switch between Modes. UP/DOWN Buttons – MIC (Microphone) Press to change channels, volume, and to select Speaker settings during programming. 1. LCD Screen Channel Number. Changes from 1 to 8 as selected by the user. CTCSS Code. Changes from 1 to 38 as selected by the user. Displays the Battery change level. When the bars are reduced, the battery needs recharging. TX Displayed when transmitting a signal. RX Displayed when receiving a signal. DCM Displayed when the Dual Watch function is turned ON. DCS Displayed when the Digital Code System is turned On. VOX Displayed when the VOX feature is enabled. SC Displays when the PMR is scanning all channels. Displayed when the Key Lock feature is activated. Displays the current Speaker volume level. Displays when the call signal is ON. 2. Installation 2.1 Removing the Belt Clip a. Pull the Belt Clip latch forward (away from the Terrain 650 ) b. While pulling the Belt Clip latch, push up the Belt Clip as shown in Figure1. 2.2 Installing the Belt Clip a. Slide the Belt Clip into the slot as shown in Figure2. A “click” indicates the Belt Clip is locked into position. 2.3 Installing the Battery pack Figure 3 Belt Clip latch Figure 1 Figure 2 Figure 4 Caution: Observe the proper battery polarity orientation when installing batteries. Incorrect positioning can damage both the batteries and the unit. a. Slide down the Battery Compartment Cover. b. Install the rechargeable battery pack by following the orientation as shown in Figure 3 (the arrow is showing and pointing upward.) c. Replace the Battery Compartment Cover. See Figure 4. Important Read these Safety Warnings before you charge the batteries. When placing the Terrain 650 in the charger, use only the power supplies listed in the user instructions supplied with the Terrain 650 . Don’t try to recharge non-rechargeable batteries. Make sure the battery compartment cover is securely locked in place when you are charging the batteries. Dispose of used batteries safely and in a way that will not harm the environment-never try to burn them or put them anywhere, they could get burnt or punctured. Don’t leave dead batteries in your Terrain 650 units. They might leak if you do. 2.4 Charging the battery pack a. Insert the small plug on the end of the mains adaptor into the Power-in Connection Jack at the back of the desktop charger. b. Plug the mains adaptor into a 240V AC, 50Hz main socket with the switch on the socket set to OFF. c. Switch ON the main socket. The Terrain 650 must be charged using the mains adaptor provided. Using any other adaptor will result in non-compliance with EN60950-1 and will invalidate any approvals & warranty. d. Place the Terrain 650 units in the charge cradle in an upright position and facing outward. The charge LED indicators will light up. e. It takes about 10 hours to fully recharge the batteries if they are completely run down. New batteries takes up to 14 hours to fully charge. f. Charging the battery pack (using adaptor) Lift up the charge socket cover located on the right side of the handset. Insert the round connector of the 9.0V DC/200mA adaptor into the charge jack. Plug the mains adaptor into a 240V AC, 50Hz main socket with the switch on the socket set to OFF. Use only power supplies listed in the user instruction. Csec AC Adaptor brand ; Model -CSD0900200G power supply Then switch ON the main socket. Battery meter The battery meter is located in the left corner of the LCD Screen. It appears like a battery with three bars inside. These indicate the amount of power available. When the battery level reaches it minimum level in PMR on mode, unit will emit two beep tones and automatically the unit will power off. The Terrain 650 can detect the battery charge in 4 levels; Battery charge at high level. Battery charge at medium level. Battery charge at low level. At this level, the Terrain 650 will emit a “beep” sound for every 10 seconds in normal mode. Battery charge at very low level. When the battery level reach it minimum level while unit is on mode, unit will emit two beep tone and automatically turn off the unit. Important: Charge the unit for 10-14 hours. CAUTION : Risk of explosion if battery is replaced by an incorrect type. Disposed of used batteries according to the instructions. Battery life The Terrain 650 has a built in power saver to make the batteries last longer. But when you are not using the units, turn them OFF to conserve battery power. Mic/spk jack Important: Always turn off the PMR units when charging. This will shorten the charging time. Main socket Charge jack 3. Operation 3.1 Transmitting range The talk range depends on the environmental and terrain. It will be reach (up to about (Highlight) 8km) in wide open space, without obstructions such as hills or buildings. Don’t try to use two PMR units which are less than...


Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien