Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Getting ready The mop pad may have already come attached to the swivel head. follow steps 1A and 1B below. 1. Attach mop pad. A. Set swivel head in mop pad, making sure toggle is located on the back. B. Tighten mop pad by pulling on elastic cord while pressing on toggle 2. Fill the water tank. A. Remove the tank by lifting straight up and away from the unit. Tip: To prevent damage to themachine, do not attempt to useyour Steam Mop Max withoutwater in the tank. 1A. 1B. 2A. 6 Operations Operations Getting ready continued B. Unscrew the cap at the bottom of the water tank and remove the insert assembly. C. Fill the water tank with water. For best results, water should be at room temperature. D. Replace the insert assembly and cap, tighten until snug. E. Replace the water tank by lining up the vertical guides and gently sliding it back into place. 3. Twist the quick release cord wrap clockwise to unwrap the power cord completely, and plug it into a 120-volt outlet as described on the Important Safety Instructions page. 4. The ready light will illuminate when the Steam Mop Max is ready for use. Before you clean Thoroughly sweep or vacuum floor prior to cleaning with the Steam Mop Max. Cleaning hard floors Your Steam Mop Max is designed to clean hard flooring such as ceramic tile, vinyl, marble, stone and sealed hard wood floors. Use of your Steam Mop Max on waxed or some unwaxed floors may result in a diminished glossiness. The Steam Mop Max is not for best results, test in an inconspicuous area and check the care instructions from your flooring manufacturer. 1. When the ready light illuminates, begin cleaning by slowly passing over the surface while pressing the steam on demand trigger to emit steam as needed. 2. To sanitize an area of your floor, (attack invisible germs and bacteria) put the center of the Steam Mop Max over the spot for a minimum of 15 seconds using continuous steam, but no longer than 20 seconds. For larger areas, overlap swivel head placement. 2B. 2E. WARNING: Never put descalingaromatic, alcoholic, or detergent products intothe steam cleaner, as this may damage it or make itunsafe for use. Tip: Upon first use of the SteamMop Max or first use of a newfilter, the pump may make a"KNOCKING" sound while filter fills with water. This is normal and will last between 30 seconds to a minute. Continue to depress thetrigger until the "KNOCKING" subsides and the unit beginsemitting steam. 800.237.7691 7 Operations Operations Cleaning hard floors continued 3. When the Steam Mop Max stops emitting steam, turn the unit off and unplug it. Simply remove the water tank, refill, plug back in, and continue cleaning. Carpet refresher attachment This accessory is recommended for the refreshing of carpets. Once the steam mop is cradled in the carpet refresher attachment, it will easily glide over the carpet. NOTE: Always be sure a moppad is in place before placingin carpet refresher attachment. Only white mop pads shouldbe used with the carpet attachment. Do not use carpet attachment on spots or stains, orglide it over the same spot forlonger than 20 seconds. 1. Attach the mop pad to the swivel mop head. As directed in step 1 on page 6. 2. Place the swivel mop head, with mop pad attached, in the carpet refresher attachment. Note: that the Steam Mop rests inthe carpet refresher attachmentand may not stay attached to theswivel mop head. It is meant toglide over the carpet. 3. Fill the water tank with water. Begin refreshing your carpet or rug by pushing the Steam Mop in a forward and backward motion, releasing steam as you go. 4. When you have finished refreshing your carpet or rug, unplug the steam mop and remove from the carpet or rug. NOTE: Move the Steam Mopand carpet refresher attachment in a continuous motion until you are finished. This product is not intended to be used as a carpet cleaner, only acarpet refresher or deodorizer. Never attempt to use the SteamMop on carpet without thecarpet refresher attachment inplace. DO NOT leave the mop in a stationary position. 8 www www.bissell.com.bissell.com CAUTION: Never put descalingaromatic, alcoholic, or detergent products intothe steam cleaner, as this may damage it or make itunsafe for use. 2 3 800.237.7691 800.237.7691800.237.7691 Maintenance and care Maintenance and care When you’re done 1. Unplug power cord from outlet. 2. Carefully remove mop pad from swivel head, as mop pad and lower assembly will be hot. 3. Any water remaining in the water tank should be emptied prior to machine storage. 4. Mop pad can be machine washed in warm water with mild detergant. For best results, air dry. Do not use fabric softeners. 5. Wrap power cord around quick release cord wrap on side of Steam Mop Max. 6. Wipe all surfaces of Steam Mop Max with a soft cloth. Store upright in a Brass Spray Tip protected, dry area. NOTE: If steam output is reduced, the nozzle may be blocked. To Swivel Head Neck remedy, unplug unit, remove swivel head from lower...