Stimmen - 5, Durchschnittliche Bewertung: 4.6
(
)
)
|
Anleitung Zusammenfassung
Unwrap vacuum flex hose completely from around unit. 1A 1B 3. Attach the tough stain brush tool to the spray trigger unit by pressing tool onto spray trigger firmly until the button lock snaps into hole. Make certain the tool is securely attached. 4. Twist the Quick Release cord wrap clockwise to unwrap the power cord completely from onboard cord storage and plug into 120 Volt grounded outlet, as described in Important 1C 1D Safety Instructions, page 3. The heat indicator light will take 30 seconds to illuminate. Water 5. Press and hold spray trigger—spray will start in a few seconds. Raise the tool slightly to check for spray. Formula Pre-treating 2 3 Cleaning effectiveness will be enhanced if you pre-treat heavily stained or highly-soiled areas. Here’s how to do it: 1. Hold the cleaning tool just above the surface of the carpet or upholstery to be cleaned. Press the trigger to release a spray of cleaning solution directly onto the soiled area. 4 5 2. Wait 3-5 minutes before cleaning. WARNING: Do not use this product while on any type of ladder. Do not place the product in a place where it will be stepped on or kicked while in use. Do not place the product on an elevated surface where it may be pulled off the surface while in use. 5 800.237.7691 Operation Operation Cleaning with your Auto Care 1. Hold the tool approximately 1” above the soiled surface. Press the spray trigger to apply the cleaning solution to the soiled area. 2. Using the brush on the tool, gently scrub the area to be cleaned. 3. For thorough cleaning, spray additional solution while the brush and suction are in contact with the surface. 4. Apply downward pressure on the tool and pull it toward you. The suction will remove the dirt and cleaning solution. Continue until no more dirt can be removed. 5. As a final step, use “drying strokes” (by not pressing the spray trigger) to remove as much liquid/moisture as possible. Repeat this step as often as necessary. Maintenance and care After cleaning 1. Unplug power cord from outlet. Note: If a significant amount of Little Green formula/water remains,it is all right to leave it in the clean/solution tank for your next cleaning task. 2. Empty and rinse the dirty/collection tank after each use, OR when dirty water reaches the indicated maximum fill line. To remove the tank, lift up the dirty/collection tank release latch and remove the tank from the unit. 3. Disconnect the cleaning tool from the spray trigger by pushing down on button lock and pulling straight off. (Do NOT twist tool to remove it) 4. Once removed from the spray trigger, clean tool by rinsing under running water. 5. Check spray nozzle for accumulated dirt or debris. If necessary, clean with soft bristle brush. Machine storage 1. Wipe all surfaces with a soft cloth. 2. Wrap power cord around the cord wrap on the back of the Auto Care. 3. Wrap vacuum flex hose around the base of the unit and secure the spray trigger. 4. Store unit in protected, dry area, at room temperature (40. to 110.F). tag is coded with an “S” (with diagonal strike-through), or says “Dry Clean Only,” do not proceed. If manufacturer’s tag is missing or not coded, check with your furniture dealer. IMPORTANT: Check the manufacturer’s tag before cleaning upholstery. “W” or “WS” on the tag means you can use your Auto Care. If Tip: Tip: Deep cleaning Check upholstery stairs and stuffing before high-traffic cleaning. Colored areas on a stuffing may regular basis bleed through can prolong the fabric when it carpet life. becomes wet. Tip: Before turning off the Auto Care, vacuum up clean water to thoroughly rinse out the interior of the vacuum flex hose. Then, lift the cleaning tool and point it upwards to drain any remaining water into the dirty/ collection tank. Tank Release Latch WARNING: Keep spray away from face. Failure to do so may result in personal injury. 166 www www.bissell.com.bissell.com 800.237.7691 800.237.7691800.237.7691 Troubleshooting Possible causes 1.2.3. Reduced spray or no spray Remedies Spray nozzle clogged 1. Clean spray nozzle Clean/solution tank empty 2. Check/fill tank Clean/solution tank insert clogged 3. Clean insert at bottom of clean/solution tank 4. Pump needs priming 4. Gently lift clean/solution tank while depressing the spray trigger OR gently squeeze clean tank while depressing spray trigger Deep cleaner won't pick up cleaning solution Possible causes Remedies 1. Tank release latch is not closed properly 1. Lift up the tank release latch and press down firmly to make sure it is in place 2. Poor upholstery/carpet tool position 2. Reposition upholstery/carpet tool on surface, follow recommended cleaning procedures 3. Dirty/collection tank is full 3. Empty dirty/collection tank 4. Upholstery/carpet tool brush worn 4. Replace with new brush 5. Excess solution in vacuum flex hose 5. Lift tool and point upwards to allow water in hose to flow into the dirty/collection tank 6. Incorrect cleaning formula 6. Use BI...