Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
You must have training in the operation of this machine before using it. If you cannot read English, have this manual explained fully before attempting to operate this machine. All directions given in this book are as seen from the operator’s position at the rear of the machine. For new books write to: ALTO U. S. Inc., 2100 Highway 265, Springdale, Arkansas 72764. Form No. 78439A 12/98 CLARKE TECHNOLOGY Printed in the U.S.A. 230 Volt Machine Instructions For Connection To The Power Supply And The Electrical Ground This machine must be connected to the electrical ground to protect the operator from electric shock. The machine has an approved power cord with two main conductors and one earthing conductor. Connect the plug to a receptacle as shown in Figure 2. The green (or green and yellow) conductor in the cord is the ground wire. Never connect this wire to any terminal other then the ground terminal. Make sure you have the correct frequency and voltage before connecting the power cord to an outlet. The machine has a plug as shown in Figure 2. If a receptacle connected to the electrical ground as shown in Figure 2 is not available, have one installed by an electrical contractor. Do not use an adapter. WARNING: This machine will operate only on AC frequency and electrical voltage shown on the nameplate. Make sure you have the correct frequency and voltage before connecting the power cord to an outlet. If you are not sure, consult your electrical contractor. WARNING: Have worn, cut or damaged cords and plugs replaced by an authorized service person. After using this machine, follow these instructions: -Store the cord on the hook. -Store the machine indoors away from sources of heat. This machine is provided with an automatically reset thermal overload to avoid damage to the motor. If the thermal overload stops the motor unplug the machine and follow the procedures below: -Empty the vacuum tank. -Shake the filter bag to remove dust. -In a few minutes the thermal overload will allow restarting of the motor. Pin Earthing Contacts European Plug Side Earthing Contacts Figure 2 CLARKE TECHNOLOGY Operator's Manual STV-20/20D Page -5 CLARKE TECHNOLOGY STV-20 Single Motor Assembly Drawing & Parts List 1/98 56 7 8 9 12 13 14 15 16 17 19 20 21 22 23 27 28 30 40 41 31 32 36 37 38 39 35 34 33 26 25 24 18 11 10 1 2 3 4 Ref. Part No. Description Qty 1 51841A Cord, Power 1 2 56448A Strain Relief 1 3 54503A Cord, Grip 1 4 56441A Screw, 5mm x 20mm 2 5 51869A Cord, Hook 1 6 88304A Screw 5mm x 50mm 4 7 54922A Handle, Lift 1 8 56482A Screw 5mm x 35mm 2 9 56441A Screw, 5mm x 20mm 4 10 88001A Screw, 5mm x 14mm 2 11 40409A Block, Terminal 1 12 88304A Screw, 5mm x 50mm 2 13 52765A Cover, Dome 1 14 56441A Screw, 5mm x 20mm 2 15 47316B Switch, Rocker 1 16 54064A Filter, Upper 1 17 88304A Screw, 5mm x 50mm 9 18 51872A Clip, Spring 1 19 57162A Plug, Upper 2 20 52799A Cover, Motor 1 21 56483A Screw, 5mm x 40mm 9 22 56483A Screw, 5mm x 40mm 3 23 58410A Support, Motor 1 24 58414A Screw, 5mm x 30mm 1 25 56442A Screw, 4.3mm x 19mm 1 26 50507A Block, Terminal 1 27 57877A Ring, Vac Motor 1 28 56441A Screw, 5mm x 20mm 4 30 54377A Gasket, Vac Motor 1 31 56039B Motor, Vac 115V 1 56046B Motor, Vac 230V 1 40834A Brush, Carbon 115V 1 40835A Brush, Carbon 230V 1 32 54377A Gasket, Vac Motor 1 33 56441A Screw 5mm x 20mm 8 34 54377A Gasket, Vac Motor 2 35 57163A Plug, Motor 2 36 54058A Foam, Triangle 3 37 54059A Filter 3 38 57164A Plug, Lower 2 39 50760A Base, Motor 1 40 59859A Washer, Star 1 41 56485A Screw, 4mm x 8mm 1 NI 59887A Wire, Connect 4 NI 52944A Clip 2 NI= Not Illustrated Page -6-CLARKE TECHNOLOGY Operator's Manual STV-20/20D CLARKE TECHNOLOGY STV-20 Filter Bag & Float Assembly Drawing & Parts List 1/98 1 2 3 4 5 6 7 8 Ref Part No. Description Qty 1 58541A Spacer, Plastic 4 2 58413A Screw, 5mm x 20mm 4 3 57856A Cage, Float 1 4 54027A Filter 1 5 53981A Float 1 6 50339A Adapter, Bag 1 7 50720A Bag, Filter 1 8 56492A Support, Filter Bag 1 To add optional filters for STV-20 or STV-20D order: 54015A Filter, HEPA 1 and 57372A Retainer 1 or 53982A Filter, Cartridge 1 and 57372A Retainer 1 Wet Vac Tools Part No. Description 59213B Tool, Squeegee 59214B Tool, Floor Brush 59215A Tool, Crevice 38mm 57503A Reducer, Wand 59860A Wand, Extenion 2 Pc. 59861A Wand, Chrome 2 Pc 54887A Hose, 38mm, 2.5m Page -8-CLARKE TECHNOLOGY Operator's Manual STV-20/20D CLARKE TECHNOLOGY STV-20 STV-20D Tank Assembly & Tilt and Pour Carriage Drawing & Parts List 1/98 1 2 3 4 5 6 7 8 91011 15 16 16 17 18 19 20 12 13 1 1 2 3 4 14 15 5 6 7 8 9 10 11 12 13 14 Tank Assembly Tilt and Pour Carriage Ref. Part No. Description Qty 1 54921A Handle, Transport 1 2 58529A Spacer, Hinge 2 3 50460A Pivot, Tank Support 1 4 57380A Rivet 4 5 56490A Support, Handle 1 6 56441A Screw, 5mm x 20mm 4 7 51868A Carriage, 20 gal. 1 8 50459A Pivot, Wheel 2 9 51184A Bearing, Spacer 2 10 59948A Wheel, 20 gal. 2 11 54897A Hub Cap 2 12 57853A Ring, Snap 2 13 56441A Screw, 5mm x 20mm 8 14 50555A Block, Stirrup ...