Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
brush OFF for when the cleaner is left running in the upright position and when the hose is in use. brush ON for normal carpet cleaning. NEUTRAL PARK DRIVE The Adaptive Brush Control is a simple device to allow cleaning of hard floors by switching off the brushbar. The height adjusts automatically. Adaptive Brush Control THE SAFETY ALERT RATCHET NOISE WARNS THAT THE BRUSHBAR IS OBSTRUCTED N P D MANUAL Pre-motor filter Soleplate Filters and blockages Rotate twist ring to the left to release filter case. Remove filter case from machine body. 1 2 1 2 3 4 3 Lift out pre-filter using handle 4 (replace at least every 12 months). Remove wand from hose and look down the wand to check for daylight. Locate blockage removal cassette catch at base of hose location. 2 Pull back catch, remove cassette and check for blockage. To replace, position at 450 and click catch back into place. Remove Cyclone assembly to check Cyclone entry and duct. 2 4 Using a coin, undo the yellow fastener to remove the quick release window. Check for blockage at the bottom of the duct and underneath the soleplate. 1 Ensure the pre-filter is changed regularly. If filters block, the cleaner may overheat and cut out. The Dyson DC03 has a built in motor protection thermostat to protect the appliance in the event of a restriction to airflow. Unplug cleaner. Leave for 30 minutes. Fit a new pre-filter before use. 1 4 Pre-motor filter Post-motor filter 3 Replace filter case and rotate twist ring down and to the right to secure. DYSON CUSTOMER HELPLINE: 0990 275104 8am to 8pm, 7 days a week Blockage removal Cyclone entry cassette catch duct NB If the cleaner is still blocked lift out the post-filter and check inside for dust caking. 3 Bin emptying and brushbar If ratchet warning noise continues, stop vacuuming, turn off the machine and unplug. To free the brushbar, lie the machine on its front to reveal the soleplate. 1 2 3 Using a coin, undo the three yellow 4 fasteners. Push bin release catch forward to free the bin. Wrap a plastic bag firmly around the rim of the clear bin and empty (wait ten seconds to allow dust to settle). To clean bin, wash in warm water. Do not remove bin inner and seals, and ensure bin is dry before reassembling. 3 4 Push Cyclone release catch forward to free Cyclone assembly. Pull Cyclone assembly away from the machine. 1 To replace brushbar, align and locate in slots. Rotate until the end caps click into place. Rotate brushbar to allow belt to centralise, then replace soleplate. 5 1 2 3 1 2 3 4 Do not fill bin above maximum line. 4 5 Keep small holes clear of dust and fluff. 2 Optional DYSON CUSTOMER HELPLINE: 0990 275104 8am to 8pm, 7 days a week If the brushbar is obstructed, a loud ratchet warning noise will be heard. Pull the cleaner away and it will automatically re-set itself. For thread removal, unplug cleaner and carefully cut away threads from brushbar. End cap of brushbar Raised section Remove soleplate and clear the brushbar obstruction. D YSON OMER E If you have any questions way. All you have to do is call 0990 275104 from 8am to 8pm, seven days a week. When calling, please have the following information O99O 2751O4 1. Serial number of your Dyson (between the wheels) 2. Your postcode 3. The date of purchase 4. Where you made your purchase Most queries can be solved over the telephone. If not, this is how our repair today overnight back to Dyson overnight back to you If you call before 11.00am (monday to friday), your cleaner will be collected after 12 noon that day. Our aim is to courier your cleaner back to the Dyson factory and return it to you repaired and tested within 48 hours. The service may take a little longer in some areas, such as the Highlands and Islands. DYSON CUSTOMER HELPLINE: 0990 275104 8am to 8pm, 7 days a week Important safety PLEASE READ CAREFULLY BEFORE USE PLEASE READ CAREFULLY BEFORE USE Check that your supply corresponds appliance must only be used as fuse to BS1362. This appliance is for your safety and convenience. A 13 Should the fuse need to be replaced, please ensure of 13 amps and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse. If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse cover, the plug must not be used until a replacement cover A replacement fuse cover can be purchased from your If the fitted moulded plug is unsuitable for the socket outlet fuse should be removed and the plug cut off and disposed of There is a danger of severe electrical shock if the cut off plug is inserted into socket. If a new plug is to be fitted, please observe the wiring code as shown If in any doubt please consult a qualified electrician. IMPORTANT The wires in this mains lead are coloured in accordance with the following code: BLUE: Neutral BROWN: Live As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your pl...