Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
CALL POWER AUDIO SHIFTMACRO TVVIDEO GUIDEREC MUTE VOLUMETUNING/SKIP THEME FAVMENU FUNCTION SHIFT SETUP INFO ALT AUDTV/SAT/VID REPEAT RANDOM+100 DISPLAY ENT+10 LISTEN MODE SOUNDSUBWOOFER 2 31 5 64 8 97 0 REMOTE CONTROL UNIT 874. 6BAND P. CALL P. CALL POWER Remote Control Instruction Manual Quick start guide.......................................... 1 Getting the most from your remote control........... 3 Setup code chart.......................................... 7 In case of difficulty......................................13 Remote operation of other components.............14 Remote Control Instruction Manual Preset Remote Control Quick Start Guide 4 This quick start guide explains how to setup the remote control to operate audio and video components other than the receiver. 2 In order to make full use of the functions of the remote control, be sure to read the section of this manual entitled “Getting the most from your remote control”. It contains a detailed explanation of how to operate the remote control and make the necessary settings. The quick start guide describes the operation of the following keys: 1 ENT key Gets you into and out of the preset code registration mode. 2 VIDEO, AUDIO, and TV keys Use these keys to select the input you want to register. 3 Numeric keys In the preset code registration mode, you use these keys to enter the code numbers that let you control your components. 4 POWER key Once you have entered the setup code for another component, you can press this key to turn power to that component on or off. This lets you confirm that you 3 entered the code properly. 1 1 This instruction manual is for some models. Model availability and features (functions) may differ depending on the country and sales area. B60-3617-00 00 CS MA (T, E2, Q, X) 99/12 11 10 9 8 7 6 5 4 3 2 1 98/12 11 10 9 8 7 6 5 4 3 2 ID Remote Control the code that matches the component. the code that matches the component. Press the POWER key to see if you can turn the component on and off. (If the component you want to control has a mechanical power key that cannot be operated by remote control, press the PLAY key or the TUNING/SKIP key to test it.) If the component does not respond when you try to control it, return to step 4 and enter the next setup code on the list. Repeat this procedure until you find Press the ENT key to store the code. Repeat steps 3 though 6 to enter the codes for each component you want to control. Once you have finished register- ing setup codes for all of the in- puts, hold down ENT key until the backlight flashes twice (about three seconds). This exists the registration mode. Quick Start Guide RC-R0507 (En/T) 2 Register the setup codes for your audio and video components If you accidentally exit the registration mode by pressing the wrong key, you will not lose any setup codes you have already saved. POWER Step 5 ENT Step 6 Step 7 ENT Step 8 ENT Step 1 Look up the setup code for the component you want to control. RC7Write down all the applicable setup codes. (This step is very important.) Step 2 Hold down ENT key until the back- light flashes twice (about three seconds). For step 2 through step 8, make sure you start the next step within five seconds of completing the previous one. If more than five seconds elapses between any two steps, you will need to go back and start over from step 2. Step 3 Press the VIDEO, AUDIO, or TV key to select the input you want to register. (Each press of the key advances you one by one through the available input settings.) The current input setting appears on the display of the receiver. Step 4 Use the numeric keys to enter the 4-digit setup code for the compo- nent. AUDIO TVVIDEO THEME FAVMENU INFO ALT AUDTV/SAT/VID REPEAT RANDOM+100 DISPLAY 2 31 5 64 8 97 0 Remote Control Automatic input naming In the initial factory setting, the remote control already has provisional component names registered for each input. Before you register setup codes, pressing the input keys of the remote control causes the display to change from the factory preset input names of the receiver (VIDEO1, VIDEO2, etc.) to the input names registered in the remote control (VCR1, VCR2, etc.). Once you have registered the appropriate setup codes for your components, pressing the input keys of the remote control causes the display to change to the actually connected component names (LD, DVD, etc.) for which you have registered setup codes. Getting the most from your remote control RC-R0507 (En/T) The remote control supplied with this receiver is also capable of controlling components from a variety of manu 3 facturers once you register the appropriate setup codes into the remote control unit. 3Press the VIDEO, AUDIO, or TV key repeatedly to select Refer to "Remote operation of other components" for de-the desired component. tails about the operations available for each component. VIDEO key AUDIO key TV key Low battery warning 1TV1 2TV2 3CABLE 1 Input Component Maker Code Key (CD) CD player KEN...