Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
CH. VOL. VOL. TUNING BAND ENTER AUTO/MONO F.SHIFT REC LEARN RANDOMREPEAT INPUT SEL. 21 3 54 6 87 9 0+10 +100 1110 12 DISPLAY TV SELECT SELECT THEMEAUDIO FAVORITE EXITINFO. LAST CHANNEL OSD /PAGE RETURN /PAGE DIMMER TITLE/GUIDE MENU LISTEN M. SUB.W. MOVIE TV AV. POWER SYS. POWER REMOTE CONTROL UNIT RC-R0808 This quick start guide explains how to setup the remote control to operate audio and video components other than the receiver. In order to make full use of the functions of the remote control, be sure to read the section of this manual entitled “Getting the most from your remote control”. It contains a detailed explanation of how to operate the remote control and make the necessary settings. The quick start guide describes the operation of the following keys: 1 Display operation 1 key Use this key to go back to the previous display or initial display. 2 Display operation 2 key Gets you into and out of the preset code registration mode. 3 Display The information for setup is displayed. 4 5/°keys Use these keys to select the source or setup code. 5 MOVIE, MUSIC, and TV keys Use these keys to select the input you want to register. 6 AV.POWER key Once you have entered the setup code for another component, you can press this key to turn power to that component on or off. This lets you confirm that you entered the code properly. Remote Control B60-4611-00 (EN) Register the setup codes for your audio and video components >VCRVideo1:Menu>> AV.POWER Step 1 Press the display operation 1 key re- peatedly until “Menu” appears in the dis- play. Step 2 Press the display operation 2 [Menu] key repeatedly until “01.IR” appears in the display. For step 1 through step 9, make sure you start the next step within 8 seconds of completing the previous one. If more than 8 seconds elapses between any two steps, press the display operation key so that the display appears. Step 3 Press the 5/°keys to select “01.IR”, then press the display operation 2 [Enter] key. Step 4 Press the 5/° keys to select the input that you want to register, then press the display operation 2 [Enter] key. Step 5 Press the 5/° keys to select the com- ponent that you want to register, then press the display operation 2 [Enter] key. Step 6 Press the 5/°keys to select the maker of the component that you want to reg- ister, then press the display operation 2 [Enter] key. Step 7 Press the 5/° keys to select the setup code. Step 8 Press the AV.POWER key to see if you can turn the component on and off. If your component has a mechanical POWER switch that cannot be operated by remote control unit, press the dis- play operation 2 [Enter] key and dis- play operation 1 [Home] key, and se- lect the component by pressing the MUSIC, MOVIE, or TV key, then press the PLAY (U) key or TUNING (2 3) key to test it. If the component does not respond when you try to control it, return to step 7 and enter the next setup code on the list. Repeat this procedure until you find the code that matches the component. When the component does not respond, select "Nothing." Step 9 Press the display operation 2 [Enter] key to store the code. >02.Surround01.IRBack Enter>AiwaKenwoodBack Enter>02:Nothing01:0056Back Enter>04.Video203.Video1Back Enter>02.Surround01.IRHome Enter>06.Cable05.VCRBack Enter>02.Surround01.IRHome Enter Repeat steps 3 through 9 to enter the codes for each component you want to control. Press the display operation 1 key repeatedly until “Menu” appears in the display. If you accidentally exit the registration mode by pressing the wrong key, you will not lose any setup codes you have already saved. Remote Control Automatic input naming In the initial factory setting, the remote control already has provisional component names registered for each input. Before you register setup codes, pressing the input keys of the remote control causes the display to change from the factory preset input names of the receiver (VIDEO1, VIDEO2, etc.) to the input names registered in the remote control (VCR1, VCR2, etc.). Once you have registered the appropriate setup codes for your components, pressing the input keys of the remote control causes the display to change to the actually connected component names (LD, DVD, etc.) for which you have registered setup codes. Getting the most from your remote control The remote control supplied with this receiver is also Registering setup codes for other components capable of controlling components from a variety of manufacturers once you register the appropriate setup codes into the remote control unit. Display Refer to "Remote operation of other components" for de- Display operation 1 tails about the operations available for each component. Display operation 2 Low battery warning Replace all four batteries with new ones when you notice a shortening of the distance from which the remote control will operate. The remote control is designed to retain setup codes in memory while you change batteries. 5/° + – + – How to use the display operation keys To...
Dieses Handbuch ist für folgende Modelle:Fernbedienungen - KRF-V8030D (323.27 kb)