Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Philips
Dateigröße: 518.22 kb
Dateiname:
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
For example - you may want to use your remote to operate the RANDOM PLAY feature from your original CD remote control. This remote is equipped with an “easy learning” feature that allows you to “learn” features (such as RANDOM PLAY from your original CD remote) by following the steps below, and on the next page: 1. Press and hold the CODE SEARCH button until the red indicator turns on, then release the button. 2. Press and release the desired mode button (TV, VCR, etc.), the red indicator blinks then stays on. 3. Press and release the LEARN button, the red indicator blinks then stays on. 4. Press and release the Learning Remote button that you want to teach (e.g. POWER). 5. Point both remotes facing each other by approximately 1 inch apart (see tips on page 15). 6. Press and hold the Original Remote button (e.g. Power) until the red indicator blinks once and stays on. If there is a learning problem, the indicator blinks for three seconds and stays on. If this happens, repeat Steps 4 to 6. 7. Repeat Steps 4-6 for other buttons you want to learn. 8. Press and release the CODE SEARCH button when all desired remote commands are learned. Code Learning is now complete. 6. Line up your remotes (that you’re learning from) in front of the Learning remote, on a hard surface approx. 1 inch apart. 2. 4. To Clear all Learned Commands under a mode Clearing learned commands is helpful if, for example, you replace your CD player with another brand or model. If you had learned a feature from your old CD player’s original remote on to this remote (such as RANDOM PLAY), that feature would no longer work for your new CD player. Should you wish to remove or clear one or more “learned” commands, follow the steps below: 1. Press and hold the CODE SEARCH button until the red indicator turns on. Release the CODE SEARCH button. 2. Press and release the button for the mode you want to clear (TV, VCR, etc.). The red indicator blinks off. 3. Press and release the LEARN button TWICE. The red indicator blinks off. 4. Press and release the CODE SEARCH button. The red indicator turns off. All learned Commands under that mode are now cleared. Master Clear - To Clear all Learned Commands under all modes 1. Press and hold the CODE SEARCH button until the red indicator turns on. Release the CODE SEARCH button. 2. Press and release the LEARN button TWICE. The red indicator blinks off. 3. Press and release the CODE SEARCH button. The red indicator turns off. All Learned commands in the remote are now cleared. MM1M2L1L23. 1,8. 18 19 Macros Macros, cont. The “M” (Macro) button, in conjunction with buttons M1, and M2, lets you to program and store up to two sequences of IR Commands (button-presses) of your choice. One press of the respective Macro digit button results in that sequence of IR commands being sent. Any sequence of commands that you regularly perform can be reduced to two button presses (“M” button followed by M1, or M2 button). For example pressing “M” followed by a single button can turn on your TV, turn on your cable box, change to your favorite channel, turn on your VCR, and tell it to record, etc. A total of 10 button presses can be stored under each of the two Macro digits. To Setup a Macro 1. Press and hold the CODE SEARCH button until the red indicator turns on. Release CODE SEARCH. 2. Press and release the “M” button. The red indicator blinks off. 3. Press and release the button where you want to store the Macro, i.e. button M1, M2. 4. Press and Release Mode button for the first device to be controlled in the Macro sequence. (The first button in a Macro sequence MUST be a Mode button (TV, VCR, etc.)). 5. Press and release the buttons you want to be included in the Macro, in the order you want them to be sent (maximum of 9). The red indicator blinks off with each button press. 6. To store the Macro, press and release the “M” button. The red indicator turns off. Note, if you program the maximum of 9 buttons, the Macro will be automatically stored on the 9th button press and the red indicator turns off. Macro setup is now complete. 4. MM1M2L1L21. 2, 6. 3. Macro Operation To activate the Macro press and release the “M” button followed (within 20 seconds) by the M1, or M2 button. Macro Notes 1. You might want to add “delays” in a Macro sequence (e.g. to allow for your TV warm-up time). Delays can be added by using the PAUSE button followed by the number of seconds delay required. For example, to enter a delay of 3 seconds, press and release PAUSE followed by 3 (in step 4 of “To Setup a Macro” on the previous page). Maximum delay is 9 seconds. It is not possible to have a “0” digit entered after Pause i.e. there is no zero delay. 2. There is an automatic delay of half a second between each IR transmission in a Macro sequence. 3. The first button in a Macro sequence MUST be a Mode button (TV, VCR, etc.). To Delete a Macro 1. Press and hold the CODE SEARCH button until the red indicator turns on. Release the CODE SEARCH button. 2. Pres...