Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
When the power supply cord or plug is damaged or frayed. B. If liquid has been spilled into the product. C. If the product has been exposed to rain or water. D. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions because improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation. E. If the product has been dropped or the cabinet has been damaged. F. If the product exhibits a distinct change in performance. • Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. • Do not use this telephone to report a gas leak in the vicinity of the leak. SAVE THESE INSTRUCTIONS Page 4 W-1000 W1000_User_Guide 4 11/15/99, 9:37 PM Safety Instructions Continued The following items are included as part of the CS-03 Requirements. The Load Number of the equipment is 20. The standard connecting arrangement code for the equipment is CA11A. NOTICE: The Canadian Department of Communications label identifies certified equipment.This certification means that the equipment meets certain telecommunications network protective operational and safety requirements.The Department does not guarantee that the equipment will operate to the user’s satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company.The equipment must also be installed using an acceptable method of connection. In some cases, the company’s inside wiring associated with a single line individual service may be extended by means of a certified connector assembly (telephone extension cord).The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier.Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user disconnect the equipment. Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together.This precaution may be particularly important in rural areas. Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. The Load Number (LN) assigned to each terminal device denotes the percentage of total load to be connected to a telephone loop which is used by the device to prevent overloading.The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the load numbers of all the devices does not exceed 100. SAVE THESE INSTRUCTIONS E N G L I S H W-1000 Page 5 W1000_User_Guide 5 11/15/99, 9:37 PM E N G L I S H D F A B E C Clarity®E W-1000 User Guide Unpacking the Walker Clarity® Inside you will find the following items: A. Handset B. Handset Line Cord (Coiled, 10 ft.) C. Base Unit D. Phone Line Cord (long, flat) E. Desk/Wall-Mounting Bracket F. This User’s Guide Carefully remove all of the contents from the package. If there is any visible damage, or any of the contents are missing, do not attempt to operate this equipment. Please call 1-800-552-3368 to exchange this unit for a factory-fresh replacement. In addition to the items listed above, you will need one of the following to complete installation of this unit: • Modular Wall Jack, or • RJ-11C Modular Jack Adapter (if you have an older 4-prong jack) RJ-11C Page 6 W-1000 W1000_User_Guide 6 11/15/99, 9:37 PM Installation Connecting the Clarity Phone: To install as a Desk Unit: • Plug one end of the telephone line cord (long, flat) into the back of the Walker Clarity. • Plug the other end of the telephone line cord into the wall jack. • Plug one end of the handset cord (coiled) into the bottom of the handset. • Plug the other end of the handset cord into the jack located on the left edge of the Walker Clarity. • Place the handset in the cradle of the Walker Clarity. Note: If you are plugging the phone into an older 4-prong jack, use an RJ11C adapter RJ-11C E N G L I S H Warning:To prevent electrical shock, always remove the telephone line cord from the wall jack before removing the cord from the telephone. Never leave the line cord connected to the wall jack if it is not also connected to the telephone. Select a Location: • The unit should be located near a wall jack for easy installation. • The unit should be located in an area where it is easy to see the lighted ringer. • The unit can be used as a desk top phone or a wall mount phone. Avoid placing the unit w...