Stimmen - 5, Durchschnittliche Bewertung: 4.2
(
)
)
|
Anleitung Zusammenfassung
Broadcast will resume when you replace the handset on cradle. AM Antenna A built-in antenna eliminates the need for an outside antenna for AM reception. Moving the unit slightly may improve reception of distant AM signals. FM Antenna The power cord acts as your FM antenna. The power cord picks up moderate to strong signals and eliminates the need for an external antenna in most strong signal areas. Be sure the power cord is stretched to its longest length. Do not coil or bunch the cord together. Changing position of the power cord may improve reception. Telephone Operation Adjusting the Ringer Volume You may control the ringer volume level with the switch located on the side of the base. = loud = low = off Handset Receiver Volume Use the VOLUME switch on the rear of the handset to adjust the handset receiver volume. = high = mid = low Flash Press the flash button to activate customer calling services, such as call transfer, which are services provided by your local phone company. Redial To redial the last number called (up to 32 digits), use the redial feature. 1. Pick up the handset. 2. Press the redial button. 3. The last number is automatically redialed. Using One Touch Redial If the last call you dialed was busy, you can redial it immediately by just pressing the redial button and without hanging up the handset. Setting Up the Caller ID Menu IMPORTANT: Do not plug the telephone into the wall jack while setting up the Caller ID menu because an incoming call may invalidate the information not yet saved. 1. Place the handset in the cradle on the base. 2. Press the menu button. the screen displays SET ^ OR . 3. Press the CID5 or 6 button to scroll among the 7 menu screens; • SET ^ OR • Local Area Code (default ” - - -”) • Regional AC’s-1 (default “- - - - - - - - -”) • CID LANGUAGE (default English) • SELECT CONTRAST (default 3) • T/P DIAL MODE (default tone) • EXIT SETUP NOTE: You may press the dial button anytime to exit the Caller ID Set Up menu. If no buttons are pressed within 10 seconds, the phone automatically exits the Caller ID Set Up menu and returns to the NO CALLS summary screen. Local Area Code The telephone uses the programmed area code to determine the number format to display when a valid Caller ID signal is received. It is also used for the Dialback feature. 1. Press the menu button. the screen displays SET ^ OR . 2. Press the CID5 or 6button until the screen displays LOCAL AREA CODE, The default setting is ”_ _ _” . 3. To enter or change the area code, press the menu button. The screen displays the area code stored in memory. The left-most digit, or a minus sign (-) flashes, indicating the unit is ready to accept the area code entry. 4. Press the CID 6 button to select a number from 0-9 in ascending order. Or press the CID 5 button to select numbers from 9-0 in descending order. 5. Press the menu button to advance to the next digit. 6. After the 3rd and last digit is entered, press the menu button to store the area code and go to the next setting. NOTE: If you make a mistake, you can simply repeat the previous steps until your area code is set. Model 29298 Caller ID BedroomPhone™ with Dual-Wake Alarms and AM/FM Radio User’s Guide Visit the GE website at: Handset Base AC power adaptor Telephone line cord Handset cord store mem redial flash tone oper pqrs tuv wxyz ghi jkl mno abc def store mem redial flash tone oper pqrs tuv wxyz ghi jkl mno abc def CID 5or6 (Caller ID button) dial (button) delete (button) menu (button) display */tone (button) redial (button) mem (memory button) store (button) flash (button) VOLUME (switch) < rev/fwrd> (reverse/forward button) sleep (button) alarm 2 off/buzzer/radio (switch) AM/FM (switch) set time/alarm (switch) radio on/off (button) volume -/+ control knob radio channel tuning knob SNOOZE (button) alarm 1 off/buzzer/radio (switch) brightness (switch) fwrd>> (fast forward button) display ringer (switch) battery power indicator SEE MARKING ON BOTTOM / BACK OF PRODUCT RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. THE LIGHTNING FLASH AND ARROW HEAD WITHIN THE TRIANGLE IS A WARNING SIGN ALERTING YOU OF “DANGEROUS VOLTAGE” INSIDE THE PRODUCT. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. THE EXCLAMATION POINT WITHIN THE TRIANGLE IS A WARNING SIGN ALERTING YOU OF IMPORTANT INSTRUCTIONS ACCOMPANYING THE PRODUCT. CAUTION: Model 29298 00023808 (Rev. 0 CAN E) 08-17 Printed in China Thomson Multimedia Ltd. 30 Eglinton Ave W., Suite 304 Mississauga, ON Canada L5R 3E7 © 2008 Thomson Multimedia Ltd. Trademark(s) ® Registered Marque(s) ® deposee(s) Modular telephone line jack Wall plate Introduction CAUTION: When using telephone equipment, there are basic safety instructions that should always be followed. Refer to the IMPORTANT SAFETY INSTRUCTIONS provi...