Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Installing the 9V battery Installation of a 9V battery is optional, however when installed, the battery provides better performance for the speakerphone. EMERGENCY QUICK DIAL 1 2 3 4 5 6 7 8 9 AREA CODE 12 MEMORY SPEAKERPHONE 1 Remove the plastic cover over the telephone memory directory. 3 Insert a 9V battery (not included). 2 Open the battery compartment door using the flat edge of a screwdriver. EMERGENCY QUICK DIAL 1 2 3 4 5 6 7 8 9 AREA CODE 12 MEMORY SPEAKERPHONE 4 Close the battery door. 5 Replace the plastic cover over memory directory. BATTERY Battery Safety Precautions For your safety, please follow these precautions: • Do not recharge, disassemble, mutilate, wet, or dispose of battery in fire. • Keep battery out of reach of children. • Replace only with 9V battery (not included). • When replacing the battery, be sure to unplug the phone line from the phone before inserting the battery. DESK OR TABLETOP INSTALLATION Plug the telephone line cord into a modular jack (RJ11C or RJ14C) and into the PHONE LINE jack on the back of the unit. 2ABC MEM DIAL FLASH STORE REDIAL 5JKL 8TUV 0OPER MUTE HOLD EMERGENCY QUICK DIAL SPEAKER 12 MEMORY SPEAKERPHONE 1 2 3 4 5 6 7 8 9 AREA CODE PHONE NUMBER 1 4GHI7PRS * 3DEF MNO 9WXY TONE 6# PULSE TONE LO VOLUME HI RECEIVERLO MED HI OFF LO HIRINGER Plug the handset cord into the handset, and into the telephone jack on the left side of the unit. Adjust the RINGER volume switch to the desired setting. Set the PULSE/TONE switch to TONE if you use Touch- Tone service; set it to PULSE if you have rotary service. Phone Cord Wrap You can remove the base plate and wrap any extra phone cord to get it out of the way; then replace the base plate. WALL MOUNT INSTALLATION The Speakerphone can be mounted on a wall phone plate (not included). EMERGENCY QUICK DIAL 12 MEMORY SPEAKERPHONE 1 2 3 4 5 6 7 8 9 AREA CODE PHONE NUMBER THIS END UP FOR DESK USE THIS END UP FOR WALL USE BASE PLATE PUSH TO RELEASE PUSH TO RELEASE Remove the Base Plate from the back FLASH STORE REDIAL by pressing down on the snap tabs located at the top, and then Rotate the handset hook. lifting it off. PHONE LINE BASE PLATE PUSH TORELEASE PUSH TORELEASE Plug the phone cord into the phone jack on the back of the unit, wrap the extra line cord around the brackets on the bottom of the base, and then thread it through the bottom of the base plate. Reverse the direction of the Base Plate and replace it by putting the tabs into the slots on the top of the unit first, and then snapping the bottom tabs into place. Connect the phone cord to the modular jack on the wall. Slip the mounting holes over the wall plate posts and slide the unit down firmly into place. PHONE LINE BASE PLATE PUSH TORELEASE PUSH TORELEASE Wall mount installation continued on next page WALL MOUNT INSTALLATION CONTINUED PULSE TONE LO VOLUME HI RECEIVERLO MED HI OFF LO HIRINGER Set the PULSE/TONE Set the RINGER VOLUME switch to TONE if you use switch as desired. Touch-Tone service; set it to PULSE if you have rotary service. Plug the handset cord into the handset and into the unit, and then hang up the phone. 2ABCMEM DIAL FLASH STORE REDIAL 5JKL8TUV0OPERMUTE HOLD EMERGENCY QUICK DIAL SPEAKER 12 MEMORY SPEAKERPHONE 1 2 3 4 5 6 7 8 9 AREA CODE PHONE NUMBER 1 4GHI7PRS*TONE 3DEF6MNO9WXY# USING THE SPEAKERPHONE SPEAKERPHONE LOCATION For best speakerphone performance, avoid the following: • Areas with high background noise. (The microphone might pick up these sounds and prevent the speakerphone from going into the receiving mode when you finish talking.) • Surfaces affected by vibration. • Recessed areas such as in a corner, under a cupboard, or next to a cabinet, which can generate an echo effect. SPEAKERPHONE USE Note the following guidelines when using the speakerphone: • The speakerphone works similar to a two-way radio in that you can only listen or talk at one time. • Stay reasonably close to the phone so that you can be clearly heard by the person to whom you are talking. • You can adjust the speaker volume by sliding the VOLUME control on the right side of the base unit. • The speakerphone indicator light comes on when the speakerphone is in use. MAKING A CALL 1 Press the SPEAKER button instead of picking up the handset. 2 Adjust volume if needed. 3 Make your call. 4 Press SPEAKER again to hang up the phone. RECEIVING A CALL Make sure that the RINGER switch is set to HI or LOW or the phone will not ring. 1 Press the SPEAKER button instead of picking up the handset when the phone rings. 2 Adjust volume if needed. 3 Press SPEAKER again to hang up the phone. SWITCHING BETWEEN SPEAKER AND HANDSET You can switch between speakerphone and handset while the phone is dialing a number, or anytime during a conversation. • Speaker to Handset — Pick up the handset. • Handset to Speaker — Press SPEAKER, then hang up handset. TIP: If you’re using the speakerphone in a noisy environment and are in listening mode, you can improve the listening performance by pressing M...