Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
This warranty is extended only to the original consumer. A purchase receipt, invoice or other proof of original purchase date will be required before warranty repairs are provided. Mail in service can be obtained during the warranty period by calling 800- 840- 0288 toll free. A Return Authorization Number must be obtained in advance and marked on the outside of the shipping carton. This warranty gives you specific legal rights, and you have other rights (which vary from state to state). If a problem with this product occurs during or after the warranty period, please contact Channel Vision Technology, your dealer or any factory authorized service center. .&+$11(/9,6,21.1 YEAR WARRANTY 5 years with homeowner registration Channel Vision Technology will repair or replace any defect in material or workmanship which occurs during normal use of this product with new or refurbished parts, free of charge in the USA, for up to one year from the date of original purchase. This warranty does not cover damages due to shipping; failures caused by products not supplied by Channel Vision Technology; or failures due to accident, misuse, abuse or alteration of the equipment. This warranty is extended only to the original consumer. A purchase receipt, invoice or other proof of original purchase date will be required before warranty repairs are provided. Mail in service can be obtained during the warranty period by calling 800- 840- 0288 toll free. A Return Authorization Number must be obtained in advance and marked on the outside of the shipping carton. This warranty gives you specific legal rights, and you have other rights (which vary from state to state). If a problem with this product occurs during or after the warranty period, please contact Channel Vision Technology, your dealer or any factory authorized service center. .&+$11(/9,6,21. TE-100 Telephone Entry System ),6&+(5$9(18(l&267$0(6$&$ . ll)$; . +773:::&+$11(/9,6,21&20l(0$,/6$/(6#&+$11(/9,6,21&20 . TE-100 Telephone Entry System TE-100 Telephone Entry System Channel Vision’s TE- 100 provides a convenient and cost effective communication link between an entrance to every telephone in the house. Features include: • Sends a distinctive ring through the telephone to alert you to a visitors arrival • Sends a signal through the receiver if the phone line is already in use • Voice activated switching between the intercom and telephone ( no buttons to push) • Can unlock two remotely located doors or gates • Interfaces with multi- room audio processors for whole- house paging • Works with lighted and non lighted doorbell buttons • Up to 1000 ft. distance to speaker, doorbell and strike • Connect 2 speakers in parallel for 2 door function Installation Step 1: Wiring the TE-100 to the house telephone line 1. Mount the TE- 100 near the incoming telephone line junction box. 2. Connect the incoming telephone line into the J3 Telco Line Input Ports. 3. Connect the outgoing telephone line to the J2 House Phone Output Ports. Step 2: Wiring from the intercom zone to the TE-100 1. Connect the pair from the speaker to the J6 “ Speaker” terminal. 2. Connect the pair from the doorbell button to the J4 “ Doorbell” terminal. 3. If utilizing a door strike, connect this pair to the J5 “ Strike 1” terminal. 4. A second door strike is available at J5 pin 3- 4 location. If utilizing this second door strike, be sure to set switch S2 to the “ Door” position. Step 3: Selecting your chime option After completing Steps 1 and 2, your TE- 100 is set up to send a distinctive ring throughout the phone system once the doorbell is pressed. However, you also can select to have the doorbell chimes sound as well by following these steps ( see diagram 2) : 1. Locate the power transformer used for the existing doorbell chimes. 2. Wire one of the transformer leads directly to one of the doorbell chimes’ input terminals. 3. Connect the other transformer lead to the TE- 100’ s J5-5 chimes terminal. 4. Run a wire from the J5- 6 chimes terminal to the available doorbell chimes terminal. You will now hear the doorbell chime and the phones ring when the doorbell button is pressed. 5. Check the S3 Chimes On/Off switch to be sure that it is set to On. You can disable the doorbell chime at any time by switching S3 to the off position. If necessary, the doorbell’s sound or “ ding dong” delay can be adjusted by turning the TE- 100’ s R63 trimmer pot. Step 4: Interface with audio systems for paging The TE- 100 includes a 600 W balanced audio output for interfacing with multi- room audio systems. The Door Strike 2, J5 pins 3- 4 are used for the audio output feature. 1. Place switch S2 into the “ Page” position. 2. Wire from the J8 terminals to the audio input of the multi- room processor. 3. Next, make connections between J5 3- 4 and the audio processor’s contact inputs. Step 5: Connecting the supply Connect the 14VDC power supply that came with the TE- 100 to the J1 input terminal. Operation The TE- 100 is operated fro...