Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
Mounting Tape Alcohol Wipe Intercom (2) Operation & Features Call Mode: In Call Mode the intercom may only be used to call the intercom network and will not be able to hear conversation from within the network. To put intercom into Call Mode place Dipswitch #1 to the UP position. Volume: To increase the intercom volume, place Dipswitch #4 to the UP position. Sensitivity: To increase sensitivity on the intercom set Dipswitch #3 to the UP position. NOTE: Dipswitch #2 is not used. Talk Button: To talk, hold down the Talk button and all intercoms in the network will receive the signal. When holding down the Talk button on a different intercom, a secure channel is created and the other intercoms in the network do not hear the conversation. Battery: The AA Alkaline batteries (not provided) will last up to a year depending on use (Lithium batteries recommended for colder environments). When the batteries are low it will emit three beeps every ten minutes. Talk Button Speaker Learn Button Dipswitch Block Mounting Intercom Step 1 Mount Intercom with small silver screws. See mounting template on page 3. Screw the top two screws halfway into the mounting surface. Place back of intercom over screws. Tighten screws. The Intercom can be mounted by using the included screws or by using the double-sided mounting tape. It is recommended to use the mounting tape on surfaces such as metal or glass. Put the remaining silver screws into the bottom holes of intercom. Tighten screws. Mounting with Screws Step 2 1 2 Step 1 Peel off white paper from mounting tape. Firmly press mounting tape on back of intercom. Peel paper from mounting tape. Firmly press intercom onto mounting surface. Clean back of intercom and mounting surface using the alcohol wipe. Mounting with Tape Step 2 Step 3 Assemble Intercom Create New Network The intercom must be programmed to at least one other intercom to become a network or it can be programmed into an existing network. Before programming, clear memory on all intercoms. Press the Learn button on the new intercom until a beep is heard. Within 10 seconds put the second intercom into Learn Mode (refer to table below). Add to an Existing Network Each intercom will emit a tone when entering programming mode. It may take up to 3-1/2 minutes for a secure network to be established. Repeat for any additional intercoms. NOTE: Do not program new intercoms to each other before adding them to the network or they will form a separate network and the memory will need to be Install 4 AA Alkaline batteries (not provided). (Lithium cleared. batteries recommended for colder environments.) Programming Intercom Each intercom will emit a tone when entering programming mode. It may take up to 3-1/2 minutes for a secure network to be established. INTERCOM LEARN MODE Press the Learn button OR until a beep is heard. Press the Learn button on the new intercom until a beep is heard. Within 10 seconds put any networked intercom into Learn Mode (refer to table below). INTERCOM LEARN MODE Press the Learn button until OR a beep is heard. HOLD ACTIVE TALK 1 3 2 4 VOLUME MONITOR CHANNEL OFF HOLD ACTIVE TALK 1 3 2 4 VOLUME MONITOR CHANNEL OFF Troubleshooting Intercom does not function. Check batteries in Intercom. When you press the Talk button you should hear a tone. Ensure Intercom is connected to a network. See Assemble & Program. Intercom is not getting expected transmission range. Keep Intercom away from trees, metal objects and electrical wiring. Do not mount intercom on a tree, masonry, or metal surface. Intercom beeps every ten minutes. The battery is low in the intercom. Replace with AA Alkaline batteries. Need to clear intercom’s memory. Press and hold Learn button, an initial beep will be heard. Continue to hold until a second beep is heard (about 6 seconds). Ensure other intercoms are not activated during this time. Once memory is clear the intercom can be programmed to a new network. Intercom can not be programmed to network. A network may contain up to 12 intercoms. It may be necessary to clear the network and reprogram all the intercoms to the network. See Programming Intercom. NOTE: Manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Changes or modifications not expressly approved by the manufacturer could void the authority to operate the equipment. Secure cover with the two large black screws. Secure Cover Troubleshooting Intercom does not function. Check batteries in Intercom. When you press the Talk button you should hear a tone. Ensure Intercom is connected to a network. See Assemble & Program. Intercom is not getting expected transmission range. Keep Intercom away from trees, metal objects and electrical wiring. Do not mount intercom on a tree, masonry, or metal surface. Intercom beeps every ten minutes. The battery is low in the intercom. Replace with AA Alkaline batteries. Need to clear intercom’s memory. Press and hold Learn button, an initia...