Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
Lucent 0954 cover.L1 3 5/9/98, 12:17 PM © 1998 Philips Consumer Communications L.P. All rights reserved. Printed in Mexico. Issue L1 Lucent 0954 cover.L1 2 5/9/98, 12:17 PM BEFORE YOU BEGIN ........................ 3 INSTALLATION................................. 4 Table/Desk Installation .......................... 4 Wall Installation ..................................... 6 TELEPHONE FEATURE SETUP .........10 Assign Intercom Number .................... 10 Set the Clock. ...................................... 10 Set Dial Mode ...................................... 10 Set for Two or Three Phone Lines ........ 11 Set Up for a Private Line ...................... 11 Change BATTERY Display ................... 11 OPERATION................................... 12 Making a Call ....................................... 13 Call Privacy ......................................... 13 Line-In-Use Lights ................................ 13 Volume ................................................ 14 Redial .................................................. 15 Auto Redial .......................................... 15 Hold .................................................... 15 Switch Between Lines ......................... 15 Mute .................................................... 16 Flash .................................................... 16 Temporary Tone Dialing ...................... 16 Conference Calls ................................. 16 Do Not Disturb .................................... 17 Transfer a Call...................................... 17 Timer ................................................... 18 TELEPHONE MEMORY....................19 Directory Card .................................... 20 Storing Numbers in Memory ............... 20 Storing a Pause in a Memory Number ............................. 20 Storing a Temporary Tone Signal in a Memory Number ...................... 20 Storing Flash in a Memory Number .... 20 Erasing Memory Numbers ................... 20 CONTENTS INTERCOM OPERATION..................21 Basic Intercom Operations .................. 22 Making an Intercom Call or Page ........ 22 Answering an Intercom Call or Page ... 22 Ending an Intercom Call or Page ......... 22 Paging All Phones ................................ 23 Answering an ALLPAGE ....................... 23 Making an Intercom Conference Call ............................... 23 Room Monitor ..................................... 23 Checking Your Station Number ........... 23 IN CASE OF DIFFICULTY.................24 EXPANDING THE 954 SYSTEM........26 CENTREX OPERATION....................27 Setup Checklist ................................... 27 Setting Up a Fourth Line for Each Station ............................... 27 Enabling/Disabling Attendant Station .. 27 Attendant Operation ........................... 28 Setting Ring Delay Duration ................ 28 Answering a Delayed Ring .................. 28 Picking Up Another Station’s Line ....... 29 1 Lucent 0954 book.L1 1 5/7/98, 10:34 AM Lucent 0954 book.L1 2 5/7/98, 10:34 AM BEFORE YOU BEGIN • You must have a modular telephone jack and electrical outlet near where you’re installing the phone. • The total length of telephone line cord used in this system is important. If the total length of telephone line cord is more than 600 feet, you may need to use a special filter device. You can call 1 800 PCC–9125 for information about this filter. You’ll need to contact a professional to install this filter. • Identify the number of phone lines you’ll use. • All connected phones must have the same Line 1 phone number for Intercom and Paging to work. • Assign a different Intercom Extension Number (11 through 22) to each 954 telephone. You’ll need to do this individually at each telephone. • Decide if you want a private line. A private line does not appear on all connected phones. 3 Lucent 0954 book.L1 3 5/7/98, 10:34 AM INSTALLATION Table/Desk Installation 1 Install 3 AAA batteries. • Press in on the tabs and remove the telephone base. • Press in on the tabs on the battery door, and remove it. • Insert 3 AAA batteries, and replace the battery door. • Replace the telephone base. NOTE: Batteries retain telephone memory in the event of a power failure. If power fails, this phone will not work. 2 Connect the telephone line cords to the telephone. NOTE: If the phone rings when you first connect the line cords, you need to set the phone’s intercom number. See “Assign Intercom Number” in the TELEPHONE FEATURE SETUP section of this manual. • Four One-Line Jacks Modular Telephone Jacks Lines 1 and 2 Modular Telephone Jacks Lines 3 and 4 Telephone Jacks Power Cord Telephone Line Cords Standard Electrical Outlet 4 Lucent 0954 book.L1 4 5/7/98, 10:34 AM INSTALLATION • Two Two-Line Jacks Telephone Line Cords Telephone Jacks Modular Telephone Jack Lines 1 and 2 Modular Telephone Jack Lines 3 and 4 Power Cord Standard Electrical Outlet 3 Connect the power adapter. Use only the power adapter provided with this pr...