Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
• A beep sounds. • To continue storing an item to another one- touch auto dial button, repeat from step 2. • To exit the programming mode, press [EXIT]. John White 234-567-8901 M1,M2,M3=Save John White 234-567-8901 • When using the Dial Lock (p. 57) or Call Restriction feature (p. 58), you cannot store an item in a one-touch auto dial button ([M1] to [M3]). 3 beeps will be heard in step 2. • You can exit the programming mode any time by pressing [EXIT]. • If a pause is required for dialing, press [PAUSE] where needed. If required, you can also insert [FLASH] in a phone number. Pressing [PAUSE] or [FLASH] counts as one digit (p. 52, 53). To erase a stored number 1 Press the one-touch auto dial button John White ([M1], [M2] or [M3]) you want to erase. 234-567-8901 • The stored item is displayed with the #1 button number (#1 to #3). 2 Press [CLEAR]. Clear? • To stop erasing, press [] (No key). =No ENTER=Yes 3 3 Press [ENTER] (Yes key) or [CLEAR]. • A beep sounds, “Clear” is displayed and the information is erased. •“Empty” is displayed. Dialing a Stored Number 1 1 Lift the handset or press [SP-PHONE/HEADSET] or a line button. 2 2 Press the desired one-touch auto dial button ([M1], [M2] or [M3]). • The stored number is displayed and dialed. OR 1 1 Press the desired one-touch auto dial button ([M1], [M2] or [M3]). 2 2 • The stored number is displayed. Lift the handset or press [SP-PHONE/HEADSET] or a line button. • You can dial numbers stored in the one-touch auto dial buttons ([M1], [M2] and [M3]) even if the Dial Lock (p. 57) or Call Restriction feature (p. 58) is on. 45For assistance, please call: 1-800-211-PANA(7262) Advanced Intercom A 2-way intercom can be set up between two extensions. Make sure that each extension has been assigned the number ([1] to [8]) (p. 17) and is connected to the LINE1/2 telephone jack of the unit (p. 11-13). Paging a Designated Extension 1 1 Press [INTERCOM]. Intercom • The INTERCOM indicator lights. • The SP-PHONE/HEADSET indicator Press EXT1~EXT8 or PAGE lights and the speakerphone turns on. • To switch from the speakerphone to the handset, lift it off the cradle. 2 Press an extension button ([EXT1] to Ex. Calling EXT. 2 [EXT8]). Intercom • A long beep is heard if the ringer pattern of Calling [2] the paged extension is a ringer tone (p. 23).* 3 After the paged extension answers, talk Ex. Intercom with EXT. 2 into the MIC (microphone) or handset. Intercom [1]-[2] • The display shows the length of the call. 00-00-00 4 4 To end the intercom, press [SP-PHONE/HEADSET] or place the handset on the cradle. • The INTERCOM and SP-PHONE/HEADSET indicator lights go out. * If 2 short beeps are heard in step 2, the ringer pattern of the paged extension is the Voice mode, the Auto Answer mode or the Room Monitor mode. Speak into the MIC or handset to page the extension for the Voice or Auto Answer mode. • If the destination extension is the Auto Answer or Room Monitor mode, “Calling” with the extension number will not be displayed on your unit. During an intercom call: >< • To adjust the handset or speaker volume, press VOLUME [] or [] (p. 26). • If the other extensions are busy with intercom or page, you will hear a busy tone and “Busy” will be displayed when you press [INTERCOM]. Wait until the INTERCOM indicator light goes out. • You can place the intercom call on hold by pressing [HOLD]. To release the hold, press [INTERCOM]. • If an incoming call is being received, you will hear two tones (incoming call tone, p. 54) and the line indicator will flash quickly. To answer the call, press the called line button. • You can switch from the speakerphone to the handset by lifting it off the cradle. To switch back to the speakerphone, press [SP-PHONE/HEADSET]. You can place the handset on the cradle. To answer a page The INTERCOM indicator light flashes quickly (for the Ringer tone or Voice mode) and the paging extension is displayed. Depending on the ringer pattern setting (p. 23), your unit will function as follows: Ringer tone (1 to 8): The selected tone rings. Voice mode: The paging party’s voice is heard through the speaker after 2 short beeps. Auto Answer mode: After 2 short beeps, the speakerphone turns on automatically.You can then talk with the caller. Lift the handset off the cradle or press Ex. EXT. 2 calling [SP-PHONE/HEADSET] or [INTERCOM] to Intercom Call from[2] answer the page. OR If your unit is set to the Auto Answer mode, just speak into the MIC. • If the ringer volume is set to OFF for Intercom, your unit will not ring. • If the ringer pattern of your unit is the Voice, Auto Answer or Room Monitor mode, the unit will not ring. To answer an intercom call directed to another extension If the paged extension user is not available, you can answer the page with your extension. Press [INTERCOM], and press [PAGE]. • If the paged extension is in the Auto Answer mode or the Room Monitor mode, you cannot answer that page. What the INTERCOM indicator means Off Intercom is free. On You ...