Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
3 INITIAL SETUP FOR A NEW “GXV-3140/T24S SYSTEM” DOOR SYSTEM: ................................................. 3 DISCOVER/CONFIGURE A GXV-3140 PHONE AUTOMATICALLY WITH AN EXISTING DOOR SYSTEM ... 5 ADD/CONFIGURE A NEW GXV-3140 MANUALLY : ....................................................................................... 8 ESTABLISH A CALL WITH T24S DOOR SYSTEM :...................................................................................... 13 INTRODUCTION: This guide has been tested for Grandstream GXV3140 IP Video Phone with firmware version 1.0.7.50 and Mobotix T24S Door System with MX-V4.1.1.7 (2011-12-15) Software. Be aware that different firmware revisions may have different web interface formats and functionalities. This guide is applicable to the following Grandstream phone models: GXV3140. This guide will cover the 3 possible ways to set up a phone for use with Mobotix T24S. INITIAL SETUP FOR A NEW “GXV-3140/T24S SYSTEM” DOOR SYSTEM: This section details how you can configure your GXV-3140 with the Mobotix T24S System automatically. To do so, please proceed as follows: 1. Unpack the GXV-3140 and attach the handset. 2. Connect the GXV-3140 video phone to the network and to the power. The phone will boot up, and request an IP address from your DHCP server. Once the phone gets an IP address it will display it as shown below: Description : F:\20120112-120235.png Figure 1: GXV3140 LCD Idle Screen 3. Connect the GXV-3140 and T24S Door Station to the switch/router as shown below : Figure 2: Connecting the GXV-3140 and T24S 4. The buttons will light up for four seconds. During this time, press the doorbell button (bottom button) until that it starts flashing. This starts automatic initial configuration, which will take around 5 minutes: . The T24S lights blink as the camera starts up. . The current T24S IP addresses and network data are announced automatically. . Each GXV-3140 phone is contacted and configured by the camera. . Each GXV-3140 phone restarts automatically each time the MOBOTIX configuration is updated. . *101 is the new SIP quick-dial number for the first GXV-3140, while the T24S has the *201 SIP quick-dial number . The phone idle screen display will change to the following : Description : F:\20120112-190509.png Figure 3: GXV3140 “provisioned by Mobotix” LCD Idle Screen 5. The T24S Door Station and GXV-3140 phone are now ready. Here is a summary of the changes made automatically on both the GXV-3140 and T24S Door Station: . SIP server in the T24S is activated automatically. . GXV-3140 IP Video phone and the T24S are configured to use DHCP, and are automatically assigned an IP address and SIP quick-dial number. . Pushing the bell button located on the camera module (if available) calls all connected GXV-3140 phones (“if they were connected to the network during the initial Setup”) (This behavior can be reprogrammed using MxEasy). . In order to call from the GXV-3140 to the T24S Door System, you only need to lift the Handset. DISCOVER/CONFIGURE A GXV-3140 PHONE AUTOMATICALLY WITH AN EXISTING DOOR SYSTEM In this section we will describe how to Discover and Configure the phone automatically using the MxEasy software provided by Mobotix (under Support > Software Downloads > MxEasy). In order to Discover/Configure the phone using MxEasy please proceed as follows: 1. Open MxEasy software . Camera . Door Station Option, you will now be prompted to the configuration page for the door bell action : Figure 4: Add a new GXV-3140 Note: GrandStream “*101” is the extension that was configured during the initial configuration. 2. Press the + sign in order to add a new phone, you will now have another field, choose Search Door Stations Devices as shown below: Figure 5: Discover the new added GXV-3140 Once the search is done you will be prompted with the list of the available GXV-3140 on your network, as shown below: Figure 6: Discovery Result 3. Select the phone you want to add to your system, once your press OK and confirm the action, the phone will reset and get configured automatically. Note: . When you configure the phone using one of the above two method described, you may at anytime lift the GXV- 3140 handset which will trigger a call to your T24S System. . In order to establish a call to another GXV-3140 configured automatically by the T24S Door system you will need to enter the SIP quick-dial number of the other GXV-3140 using the telephone keypad and press the send key (green phone) before picking up the handset. Figure 7: Example of your Door System ADD/CONFIGURE A NEW GXV-3140 MANUALLY: This section details how you can configure your GXV-3140 with the Mobotix T24S System manually. To do so, please proceed as follows: 1. First, ensure that you have created the extension that you wish to use with the phone in T24S. Here is a quick description on how to create the extension on the Mobotix T24S System : a. Access the Admin Menu –> Sip Server Settings, you will be prompted to ...