Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Cisco Systems Dateigröße: 872.31 kb Dateiname: Unterrichtssprache:

Follow these steps to change the sound used by the ringer. Procedure Step 1Press the Settings button. Step 2From the Settings menu, use the Navigation button to select Ring Type and press the Select softkey. Step 3If you have multiple lines, use the Navigation button to scroll through the list of your lines. When you find the line you want to configure, press the Select softkey. NoteYou can only use six different ring tones on your phone, If you have more than six lines, some of your lines must share a ring tone. Step 4Use the Navigation button to scroll through the list of ring types and press the Play softkey to hear the selected ring type. Step 5When you find the ring you want, press the Select softkey to check the corresponding check box. To set the ring tone back to the default ring tone, select Default from the list. Step 6Press the OK softkey to accept and save your ringer selection. Step 7Press the Save softkey to save all of your settings and to exit the Settings menu. Related Topics •Adjusting the Handset, Speakerphone, and Headset Volume, page 2-1 •Adjusting the Ringer Volume, page 2-2 •Changing the LCD Screen Contrast, page 2-5 Adjusting the Message Waiting Indicator Light You can change the behavior policy of the message waiting indicator light (or “lamp”) for each line appearance on your Cisco IP Phone. The message waiting indicator is the red strip on your phone’s handset that blinks when you receive an incoming call. In its default state, the message waiting indicator light is usually configured to remain lit when you receive a new voice mail message. However, the default policy is determined by your system administrator. Follow these steps to specify the message waiting indicator light policy (on, off, or default) for one or more of your phone lines. Before You Begin Log in to the User Options web page. For information on the User Options web page and how to access it, see the “Logging In to the User Options Web Pages” section on page 1-16. Procedure Step 1From the User Options web page, click Change the Message Waiting Lamp policy for your phone. The Change Your Message Waiting Lamp Policy page appears. Step 2Click the drop-down list that corresponds to the line that you want to change. Choose Use System Policy, Always light, or Never light. Step 3Click Update. Step 4When you are finished, click Return to the Menu or Log Off at the bottom of the page. Related Topics •Using Voice Mail, page 3-21. Changing the LCD Screen Contrast To improve the readability of the LCD screen, follow these steps to adjust the contrast. Procedure Step 1Press the Settings button. Step 2From the Settings menu, use the Navigation button to select Contrast. Step 3Perform one of the following: •To set the desired contrast level—press the Up or Down softkeys (or the Volume buttons). •To restore your previously saved contrast setting—press the more softkey and then the Restore softkey. •To restore the factory default contrast setting—press the more softkey and then the Factory softkey. Step 4Press the OK softkey to accept and save your changes. Related Topics •Adjusting the Handset, Speakerphone, and Headset Volume, page 2-1 •Adjusting the Ringer Volume, page 2-2 •Personalizing the Ringer Sound, page 2-3 •Adjusting the Message Waiting Indicator Light, page 2-4 Changing the Language for the Phone LCD Screen Use this procedure to change the default language in which information is displayed on the Cisco IP Phone’s LCD screen. NoteIf you use the Cisco CallManager Extension Mobility service, follow the procedure described in the“Changing the Default Language for the User Options Web Pages” section on page 1-17. This procedure allows you to change the default language for your device profile. Before You Begin Log in to the User Options web page. For information on the User Options web page and how to access it, see the “Logging In to the User Options Web Pages” section on page 1-16. Procedure Step 1From the User Options main menu, select your phone from the “Select a device to configure” drop-down list. Step 2Click Change the Locale for this phone. The Select a User Locale for your Phone page appears. Step 3Select the language that you want to use as the default language from the “User Locale for this phone” drop-down list and click Update. The language that you have selected now serves as the default language for your Cisco IP Phone LCD screen. If you change the default language for your phone’s LCD screen while you are on an active call, the phone waits for you to end the call before updating the LCD screen. Step 4When you are finished, click Return to the Menu or Log Off at the bottom of the page. Related Topics •Changing the LCD Screen Contrast, page 2-5 •Changing the Default Language for the User Options Web Pages, page 1-17 3 Placing a Call and Other Basic Phone Tasks Basic phone tasks include placing, receiving and forwarding calls. The following sections describe how to perform these basic tasks on your Cisco IP Ph...

Herunterladen

Geben Sie zwei Ziffern: