Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Part 2 © Copyright 1998 Philips Consumer Communications L.P. All rights reserved. Printed in Mexico. Issue 1AT&T 848229506 INSTALLATION Open battery compartment. Install 4 AA batteries. Remove the base. SETTING UP THE SYSTEM 1 Install the batteries. a Turn the unit upside down. b Lift the base off the phone by pushing in on the triangle at the center of the large end of the base. c Swing open the battery compartment door by pressing the tab. d Insert 4 new AA batteries. e Close the battery compartment door. Leave the base off. 2 Set the Dial Mode switch. Set the switch to TT (touch tone) or DP (dial pulse) according to your telephone service. TABLE/DESK INSTALLATION 1 Connect line cord(s) to the telephone. • For two-line jack — Use only the 7-foot line cord with the clear modular plugs. Plug one end into the jack labeled L1 OR L1/L2 on the bottom of the phone. • For two separate jacks — Use both 7-foot line cords. Insert one end of the cord with the blue plugs into the jack labeled L1 OR L1/L2 on the bottom of the telephone. Insert one end of the cord with the clear plugs into the jack labeled L2. 2 Attach the base. Place the cord(s) you have attached to the telephone in the channel on the underside of the phone. Turn the base so the larger end is toward the top of the phone. Reattach the base by inserting the bottom tabs into the slots indicated. The cord(s) should go beneath the base and reappear on the other side. Push in on the triangle at the top center of the base to lock it into place. The telephone should sit flat during use. 3 Connect the handset to the telephone. Plug the coiled cord into the handset jack on the side of the phone. Plug the other end into the handset and hang up. 4 Connect the line cord(s) to your modular jack(s). • For two-line jack — Plug the free end of the line cord into the jack. • For two separate jacks — Plug the free blue plug into the modular jack for Line 1. Plug the free clear plug into the jack for Line 2. 5 Plug the system into a standard electrical outlet not controlled by a wall switch. 6 Wait for the system to initialize. When the system is first connected to power, all the indicator lights flash. Then the system counts down from 17 to 0 in the message window. 7 Check for dial tone. Press L, then press l, and listen for a dial tone on each line. Press K to turn the speakerphone off. If either line lacks a dial tone, see "In Case of Difficulty" in this manual. 8 Confirm line numbers. Press L and dial one of your telephone numbers. If you hear a busy signal, this is the number for Line 1. If it rings, it’s the number for Line 2. INSTALLATION Reverse the handset tab. WALL MOUNTING INSTALLATION 1 Connect line cord(s) to the telephone. See Step 1 in Table/Desk Installation. Two-line jack — Use the 8-inch line cord, and plug into the jack labeled L1 OR L1/L2 on the bottom of the phone. Two separate jacks — Use the 8-inch line cord, and the 7-foot line cord with blue plugs. 2 Attach the base. See Step 2 in Table/Desk Installation. 3 Reverse the handset tab. Hold down the switchhook and slide the tab up and out of its slot. Turn the tab so the curved end is up, and insert it back in the slot. Set the Dial Mode switch. 4 Connect the line cord(s) to the modular jack(s), and mount the phone on the wall. Two-line jack — Plug the free end of the 8-inch cord into the wall jack. Two separate jacks — Plug the free end of the 8-inch cord into the jack where the phone is to be mounted, and plug the free end of the 7-foot cord into the other jack. Place the phone on the wall jack mounting studs and pull down until it is held securely. 5 Connect the handset to the telephone. Plug the coiled cord into the handset jack on the side of the phone. Plug the other end into the handset and hang up. 6 Follow Steps 5-8 in Table/Desk Installation. Place line cord in channel. Connect the line cord, as described in instructions. SETTING THE CLOCK The clock records the day and time each message is received. 1 Press C. You hear a day. 2 Press a number button (1 to 7) to choose the current day (Sunday - Saturday). 3 Press C. You hear a time. 4 Use the number buttons to enter the correct time. 5 Press * for AM or #for PM. 6 Press C. If you have entered a valid time, you hear the new day and time. If you hear five rapid beeps, repeat Steps 1-6. SELECTABLE DIAL INFORMATION This telephone has a push button dial which will work with tone or dial pulse (rotary) service. Even when set to dial pulse service, the phone can be switched temporarily to tone, for access to some tone-activated computer systems. IN CASE OF DIFFICULTY If you have difficulty operating this phone, try the suggestions below. If you still have trouble, call 1 800-722-9125. NO DIAL TONE . Make sure all plugs are connected properly. Inspect the line cord connections at the modular jack and at the telephone. Also inspect the coiled handset cord connection at both ends. . Unplug the telephone and connect it to another modular jack. CALL CANN...