Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Position the Indoor Unit Mounting Plate (4) against the wall, aligning the four small rectangular openings in the Mounting Plate with the four pre-drilled holes in the wall. Screw four Screws (5) with four Washers (5) into the plastic Wall Anchors (5) to secure the Mounting Plate to the wall. NOTE: Use a leveling device to ensure the Mounting Plate is straight and level before tightening the Screws. (See Figure C.) OUTDOOR UNIT MOUNTING PLATE(7) SCREW (8) SCREW (8) SCREW(5) WASHER(5) WALL ANCHOR(5) 5 FT. FIGURE DLoosen the two Screws (8) and remove the Outdoor Unit Mounting Plate (7) from the Outdoor Unit (11). (See Figure D.) Select a location for the Outdoor Unit Mounting Plate (7) to be mounted to the exterior wall, making sure to avoid direct sunshine and rain. Position the Outdoor Unit Mounting Plate (7) against the wall at a height of five feet from the floor/ground surface. NOTE: Make sure to use a leveling device to ensure the Mounting Plate is straight and level against the wall. (See Figure D.) Using the two small openings in the Outdoor Unit Mounting Plate (7) as a template, mark the spots where two 1/8” diameter holes will be drilled in the wall. (See Figure D.) Temporarily remove the Outdoor Unit Mounting Plate (7) from the wall. Then, drill the two pre-marked 1/8” diameter holes in the wall. (See Figure D.) Insert one plastic Wall Anchor (5) into each of the two pre-drilled holes in the wall. (See Figure D.) Position the Outdoor Unit Mounting Plate (7) in a shaded spot against the wall, aligning the two openings in the Mounting Plate with the two pre-drilled holes in the wall. Screw two Screws (5) with two Washers (5) into the plastic Wall Anchors (5) to secure the Mounting Plate to the wall. NOTE: Use a leveling device to ensure the Mounting Plate is straight and level before tightening the Screws. (See Figure D.) To Connect The Wiring: Note: The Outdoor Unit (11) is factory pre-wired with approximately fifty feet of Telephone Cord (6). If more length is required between the Indoor Unit (1) and Outdoor Unit, use RVV5 x 0.5 mm2 cord (not included). (See Assy. Diagram.) WARNING! Avoid accidental electrical shock. If running the Telephone Cord (6) within wall, floor, or ceiling spaces from the Outdoor Unit (11) to the Indoor Unit (1) check hidden areas within the spaces to avoid cutting into live electrical wires, gas and water pipes. (See Assy. Diagram.) Place the Outdoor Unit (11) in its Outdoor Unit Mounting Plate (7), and secure the Outdoor Unit to the Mounting Plate by tightening the two Screws (8). (See Figure D and Assy. Diagram.) Hang the Indoor Unit (1) on its Indoor Unit Mounting Plate (4). (See Figure C and Assy. Diagram.) Run the Telephone Cord (6) from the Outdoor Unit (11) to the Indoor Unit (1). Then, connect the plug of the Telephone Cord to the receptacle on the Indoor Unit. (See Assy. Diagram.) Connect the plug of the AC Adapter (3) to the power input socket on the Indoor Unit (1). Then, plug the AC Adapter into the nearest 120 volt, grounded, electrical outlet. (See Assy. Diagram.) Note: The Video Doorphone may also be wired to control an electronic door lock (not included). Refer to the “Electrical Schematic” in this manual for wiring instructions. OUTDOOR UNIT FEATURES CAMERASPEAKERLABEL AREACALL BUTTONMICROPHONEOUTDOOR UNIT(11) FIGURE E INDOOR UNIT FEATURES HANDSETPOWER ON INDICATORMONITORELECTRONIC DOORUNLOCK BUTTONALARM BUTTONMONITOR BUTTONFIGURE F OPERATING INSTRUCTIONS Note: The Camera on the Outdoor Unit (11) has a maximum field of vision of approximately 13 feet. (See Figure E.) To operate the Video Doorphone, press the Call Button on the Outdoor Unit (11). A chime will immediately sound on the Indoor Unit (1), and the visitor’s image will automatically appear on the Monitor of the Indoor Unit. (See Figures E and F.) Pick up the Handset on the Indoor Unit (1) and you can speak with the visitor. The visitor’s image will disappear from the Monitor when you hang up the Handset. (See Figure F.) An image of the visitor on the Monitor will last for one minute, and then disappear. By pressing the Monitor Button on the Indoor Unit (1), the visitor’s image will reappear for another sixty seconds or until you hang up the Headset. (See Figure F.) You must pick up the Handset on the Indoor Unit (1) to operate the Electronic Door Opener (if an electronic lock is used). To operate, simply press the Electronic Door Unlock Button on the Indoor Unit. (See Figure F.) Note: The Alarm Button, located on the indoor unit, activates an alarm on the outdoor unit when pressed. It is designed to deter unwanted guests or summon help. (See Figure F.) IMPORTANT: Always hang up the Handset when the Video Doorphone is not in use. REV 07b PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER T...