Stimmen - 5, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
The battery icon indicates the amount of charge remaining in the Battery Pack. The level indications are approximations of the remaining Battery Pack life. They do not indicate equal amounts of Battery Pack Life. When only one level remains, the Battery Pack needs to be charged. * The Voicemail icon is activated when a new voice mail message is received if the feature is supported by the phone emulation. It appears to the right of the Signal Strength icon. Battery Low This message displays and an alarm sounds when the WT is in standby mode and the Battery Pack is critically low. The WT cannot be used until the Battery Pack is charged. [No Service message] If warning tones are not disabled, an alarm will sound and a descriptive message displays when the handset cannot receive or place calls. You may be outside of the covered area. Walk back into the covered area. The in-service tone indicates service is re- established. The signal strength icon indicates the strength of the signal and can assist the user in determining if the WT is moving out of range. The download icon indicates that the WT is downloading code. This icon only appears while the WT is running the over-the-air downloader. It appears to the right of the Signal Strength icon in the same location as the Voicemail icon. [Melody] A melody is played after the WT is powered on for the first time following a completed charge (Charge Complete). Modes of Operation The WT uses different amounts of power and bandwidth in different modes of operation. Bandwidth is provided by access points located throughout your facility. Bandwidth availability varies by type of access point. The Battery Pack in your WT provides about four hours of talk time or 80 hours in the standby mode (see below). If push-to-talk (3626 WT only) is allowed in the Admin menu and enabled by the user, standby Battery Pack life is decreased to about 30 hours. Conservation of battery life and bandwidth is possible when you understand the modes and use them appropriately. Standby mode In the standby mode the WT is waiting for an incoming call or for the user to place an outgoing call. The extension number is shown on the display and there is no dial tone. In this mode, the WT is conserving battery power and bandwidth. You may set certain preferences in the user option menu described later. This menu is accessed from the standby mode. It is important to return to the standby mode after finishing a call by pressing the End Call key. Unless otherwise directed, the following instructions for using the WT assume that it is in standby mode. Active mode To place a call, press the Start Call key. This transitions the WT to active off-hook mode. There is a dial tone, the WT is in communication with the PBX, and the display shows information as it is received from the PBX. The WT is also in the active mode when you receive a call. In certain PBX integrations, some features are designed to be accessed from an active on-hook mode. To go on-hook while still active, you may be directed to press the Line key or a Release feature key. . Whenever you are in active mode, whether off-hook or not, the WT requires the most bandwidth of any mode. To conserve bandwidth and battery power, when you have completed a call or are finished accessing active mode menus and features, press the End Call key to exit the active mode and return to the standby mode. Push-to-talk mode 3626 WT only The push-to-talk mode utilizes a common channel for incoming and outgoing radio communication. Outgoing communication uses the same amount of bandwidth as the off-hook mode. Incoming communication uses about half as much. Basic Operation Turn the WT on Press and hold the Power On key for about one second, until two chirps sound. Release the key. The in-service tone sounds and the extension number displays. The WT is now in standby mode, ready to make and receive calls. Turn the WT off While in standby mode, press and hold the Power Off key. One chirp sounds and the WT turns off. The WT cannot be directly turned off during a call. End the call first and then turn the WT off. Make a call or go off hook Press the Start Call key and then dial the number. Select a line If multiple lines are available, your telephone system may require you to select a line before dialing a number. Press the LINE key and the number key of the line you wish to use. You will hear a dial tone. Dial a number Dial calls with the WT exactly as with your desk phone. You may dial extension numbers, internal numbers, or make external calls, depending on the setup of your PBX. You willhear a dial tone, then press the number keys to dial the number. Answer a call The WT will ring or vibrate to alert you to an incoming call. Additionally, a line number on the display may flash, and the display may show information about the call, such as caller’s name and extension. To answer a call, press the Start Call key, hold the earpiece to your ear and speak with a normal tone of...