Stimmen - 2, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
The phone will redial up to 31 digits. HOLD PROG TONE LO HI FLASH REDIAL AMPLIFY Figure 14 - Redial Button Flash Press the FLASH button shown in Figure 15 to access special services available from your local phone company such as Call Waiting and 3-Way Calling. HOLD PROG TONE LO HI FLASH REDIAL VOL AMPLIFY Figure 15 - Flash Button 8 8 Figure 18 - Telephone Keypad 8 Figure 18 - Telephone Keypad Special Features Programming the Memory Buttons You can automatically dial twelve programmed telephone numbers using the memory buttons shown in Figure 16. Each button can be programmed (or reprogrammed using the same procedure) for a phone number up to 15 digits long. 1 A B C2 3 M3 M4 M5 M6 M9 M11 M10 ¤ Figure 16 - Memory Buttons To program a button, follow these steps: 1. Lift the handset and press PROG as shown in Figure 17. 0 # HOLD PROG TONE LO HI FLASH REDIAL VOL AMPLIFY * Figure 17 - PROG Button 2. Enter the phone number on the keypad (Figure 18) just as you would dial it normally. Note: Press REDIAL if you want to insert a brief pause between two numbers. DIALOGUE XL 40 1 A B C G H I T J K L M N O D E F2 3 4 5 6 7 9 #* Q R S X Y ZP W 3. Press PROG (Figure 17) once again. 4. Press a memory button (Figure 16) to store this number on that button. 5. Immediately hang up the handset. Note: Any number previously stored at that button number will be overwritten. 6. To change a stored number, repeat the programming process starting with step 1. Note: Do not program 911 in any memory button. Special Features (continued) Direct Audio Output The AUDIO OUTPUT socket allows you to connect the XL-30 to a hearing aid, neck loop, cochlear implant or other assistive listening devices. To use this port, plug in a compatible auxiliary cable and connect it to your assistive listening device. Speak into the handset when you use the Audio Output connection. DIAL AUDIO OUTPUTT RINGER RING TONE Lo HiOff Lo Hi Figure 19 - Audio Output Socket Outgoing Voice Amplification The XL-30 can amplify your outgoing voice by up to 15 dB. To use this feature, set the outgoing voice amplifier switch to AMPLIFY (underneath the unit). Note: Even with the AMPLIFY switch ON, the voice of your callers can still be amplified by up to 15dB. Note: The factory pre-setting is NORMAL. Cochlear Implant Adapter Cord A cochlear adapter cord is available from Ameriphone that can be used to directly connect the XL-30 into a speech processor. E N G L I S H 10 Special Features (continued) Connecting the Speech Processor: Caution: Before plugging any cord into your speech processor, you must consult your implant manufacturer. • Plug the mono end of the plug into the speech processor. • Plug the stereo end of the plug into the Audio Output socket on the phone. • Speak into the handset when using the Cochlear Implant Adapter Cord. HOLD PROG TONE LO HI FLASH REDIAL VOL AMPLIFY M1 M2 M5 M6 M7 M8 M9 M10 M11 M3 M4 ¤ WARNING! During thunderstorms, avoid using telephones. Electric shock from lightning can occur. Troubleshooting Chart E N G L I S H The chart below will help you solve most problems that may arise during operation of your telephone. Should the difficulty continue, contact Ameriphone or your authorized dealer for assistance. SYMPTOM CAUSE AND CORRECTIVE ACTION No dial tone Check all phonecord connections. No number dialed when memory button pressed No number stored in that memorybutton. See: “Programming theMemory buttons”, P. 9. Call cannot be dialed, or dials very slowly See “Setting UpYour Phone” to reset the dial mode switch, P. 4, 5. Call comes in but phone does not ring. 1. Check that line cord is not loose. 2. Check battery Ring flasher not very bright Check and replace the 9 Volt battery 12 Regulatory Compliance Part 68 of FCC Rules Information This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug, RJ11 USOC, is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details. The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format U...