Stimmen - 2, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
Connect the curly cord to the handset and to the socket marked q on the telephone. 2. Replace the handset. 3. If supplied, connect the mains adapter to the DC 9V socket on the telephone and to the mains power wall socket. If a power adapter is not used then batteries must be fitted! See “Batteries” section. 4. The display flashes the alarm setting. If not, hold vpressed down for around 4 seconds. 5. Press 0. 6. Scroll to the desired language using v/V. Press 0 7. Scroll to the desired contrast setting (2=normal) using v/V. Press 0 8. Scroll to the desired hour (00-23) using v/V. Press 0 9. Scroll to the desired minute using v/V. Press 0 10.Scroll to the desired day using v/V. Press 0 11.Scroll to the desired month using v/V. Press 0 12.Scroll to the desired pause setting (2 seconds=normal) using v/V. Press 0. 13.Ensure the correct dialling method is displayed (ie: TONE). Press 0. 14.Ensure the correct Recall time is displayed (ie: 100 (AU/UK/EU)/270 (FR) /600 (NZ)). Press 0. 15.Connect the telephone cord to the network wall socket and to the socket marked T on the telephone. 16.Lift the handset and listen for the dial tone. Changing the clock, alarm settings, language or contrast If you want to alter the clock, alarm, language or contrast at a later point, press and hold v for around 4 seconds and repeat steps 4. -14. above. Batteries For caller identification, memory and other functions to function in the event of a loss of power, the telephone requires 3 type AAA 1.5V batteries. When the batteries are running low, the symbol will illuminate. Use high quality batteries only. 1. Unplug the telephone cable and remove the cover. 2. Insert the batteries according to the markings for plus and minus terminals. 3. Replace the battery cover. EN 1 English Operation Making a call Regular dialling 1. Pick up the handset. 2. Enter the desired number. Dialling using correcting function You can change the telephone number before it is connected. 1. Enter the required number. Mistakes can be erased using C. 2. Lift the handset OR press . If you wish, you can switch between handset mode and handsfree mode during the call by simply pressing s or lifting the handset. Redial function If the number dialled is engaged or if you wish to redial the last number dialled, lift the handset (or press s) and press the redial button r. Volume control The handset earpiece volume may be adjusted during a call using . Ring signal There is a ringer properties switch underneath the telephone: Ring volume n Ring melody Ringer tone EN 2 English Operation The display In standby mode (handset down, no dial tone) the display will show the date and time, number of new and total number of calls stored in the Caller ID memory. Immediately following the connection of a call, a call timer will be shown on the display. The timer is a simple way to help you keep track of how long the call lasts. Handsfree function 1. Press s. The handsfree function (speaker) will be activated and the LED indicator next to the button will illuminate. 2. Dial the telephone number. To adjust the speaker volume, use the volume control on the side. 3. Speak towards the microphone located on the front edge of the telephone. 4. Press s to terminate the call. If you wish, you can switch between handset mode and handsfree mode during the call. Please note! Please remember that in handsfree mode it is only possible for one person at a time to talk. The switch-over between speaker and microphone is automatic and dependent on the sound level of the incoming call and the microphone respectively. It is therefore essential that there are no loud noises, e.g. music, in the immediate vicinity of the telephone, as this will disrupt the handsfree function. Message Waiting indicator Some PBX systems use a function called Message Waiting. The telephone can be made to indicate this by having the Indicator flash in standby mode. There is a switch located underneath the telephone for this (MW). This function operates differently depending on the PBX in question. Please contact the system controller for more information. The following four alternatives are available: LED+, LED-, ringer indicator ( ) and high DC voltage (HV). When the telephone is used in systems without telephone exchanges, the ringer indicator ( ) should be selected. EN 3 English Operation Selecting headset or handset and speaker function On delivery, the telephone is set for the handset and speaker function, but there is also a simpler headset function. The headset is instead connected to the handset and the s/= button is used to connect/disconnect to the line (corresponding to lifting and replacing the handset). Please note that the speaker function will not work when the headset function is activated. Activate the function by setting the switch y/= underneath the telephone to =. Connection of headset Disconnect the handset coil cord from the y/= socket firstly, then connect the headset. Important: Even though the handset i...