Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Do not connect your new unit to your computer before installing the drivers. Tips If you accidentally begin installation with your unit connected and the Add New Hardware Wizard or Found New Hardware Wizard dialog box appears, click the Cancel tab. Installation Steps: 1. Insert the Installation CD into your CD-ROM drive. The installation program should start automatically. Follow the on-screen instructions to finish up the installation. 2. Click the “Speaker Phone Driver” icon to install device driver. 3. Select “User Guide” to know more about detail setting. Settings Audio setting 1. To use this device, you will need to have Microsoft Windows ME/2000/XP/Vista installed on your computer. 2. To use this device for internet communication, you must have a broadband internet connection and applicable software which supports audio calls (such as Skype) installed properly on your computer. 3. You can verify and adjust the audio settings by following these steps: i. In the Windows Start menu, go to Control Panel ii. Select the Sound and Audio device icon iii. In the Audio tab, click on the volume button, a Volume Control screen appears iv. You can adjust the volume of the microphone and speaker by using the control buttons located at the front of the unit directly. Tips 1. If you cannot hear any sound from the unit, close all your current applications. Select Start • Control Panel ->Sounds and Audio devices -> Audio -> then select “C-Media USB audio Device” as the default Windows Audio device for both sound playback and sound recording. 2. To check volume settings or when there is no sound from the unit, repeat step 1) above to select Sounds and Audio devices -> Volume -> make sure that “Mute” check box is not checked. When you select Advanced button, a “Volume Control” screen pops-up. You may adjust volume up or down accordingly. 3. To check microphone settings, bring up the “Volume Control” screen, click Advanced button and select Options -> Properties -> Adjust volume for -> Recording. 4. Make sure “Recording” is checked and click OK, there will be a new Advanced button. Select “Options -> “Advanced Controls -> Other Controls”. Make sure that “AGC” is not checked. 5. If your unit’s LED changes from “blue” to “red” color, it is in mute recording state. Press the “Microphone Mute” button on your unit once and the LED will change back to “blue” again. Useful information 1. Connect your Speaker Phone directly to the available USB port. Using an extended cable or USB hub device is not recommended. 2. For stereo sound of audio playback or private conversation, stereo headphones can be plugged into 3.5mm stereo headphone jack located on the side of the unit. FCC Certification This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference, received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency, energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Consult the dealer or an experienced radio/TV technician for help. -Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. CAUTION Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FOR EUROPE “The unit is in conformity with the EMC directive and low-voltage directive.” Disclaimer Information in this document is subject to change without notice. The manufacturer does not make any representations or warranties (implied or otherwise) regarding the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any other commercial damage, including but not limited to special, incidental, consequential, or other damages. No part of this document may be reproduced or transmitted in any form by any means, electronic or mechanical, including photocopying, recording or information recording and retrieval systems without the express written permission of the manufacturer. WEEE LOGO Disposal of Old Electrical & Ele...