Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
8 Image is stretched when displaying a "widescreen" DVD title When you play a DVD encoded in anamorphic or 16:9 aspect ratio you may need to adjust the following settings: • If you play an Letterbox(LBX) format DVD title, please change the format to Letterbox(LBX) in the projector OSD. • If you play a 4:3 format DVD title, please change the format to 4:3 in the projector OSD. • If the image is still stretched, you will also need to adjust the aspect ratio. Set up the display format to 16:9 (wide) aspect ratio on your DVD player. 9 Image is too small or too large • Adjust the zoom lever on the top of the projector. • Move the projector closer to or further from the screen. • Press "MENU" on the remote control or on the control panel. Go to "Image --> Aspect Ratio" and try different settings. 10 Image has slanted sides • If possible, reposition the projector so that it is centered on the screen. • Press the "Keystone / " button on the control panel or press the "Keystone / / / " on the remote control until the sides are vertical. 11 Image is reversed • Select "Image --> Projection" on the OSD and adjust the projection direction. English EnglishEnglish 36 OSD Messages # Condition Message Reminder 1 Message Fan Fail -the system fan is not working. Projector Overheated - the projector has exceeded its recommended operating temperature and must be allowed to cool down before it may be used. Replace the lamp - the lamp is about to reach its maximum lifetime. Prepare to replace it soon. 37 Problems with the Projector # Condition Solution 1 The projector stops responding to all controls If possible, turn off the projector, then unplug the power cord and wait at least 30 seconds before reconnecting power. 2 Lamp burns out or makes a popping sound When the lamp reaches the end of its useful life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp" section. English 38 LED & Alarm Definition Listing LED Messages English Message Lamp LED Temp LED Power LED Red Red Red Blue Standby (power cord plugged in) -- V -Power button ON -- - V Lamp retry -- - Quick flashing Turning off (cooling state) -- Quick flashing -Turning off (cooling completed) -- V -Error (thermal failure) -V -V Error (fan lock failure) -Quick flashing -V Error (lamp breakdown) V -- V Error (color Wheel fail) Quick flashing -- V 39 English Replacing the Lamp Use a screwdriver to remove the screw(s) from the cover, and then pull out the lamp. The projector will detect the lamp life. You will be shown a warning message "Lamp is approaching the end of its useful life in full power operation. Replacement Suggested!" When you see this message, change the lamp as soon as possible. Make sure the projector has been cooling down for at least 30 minutes before changing the lamp. Warning: The lamp compartment is hot! Allow it to cool down before changing the lamp. To Change the Lamp 1 Turn off the projector by pressing the power button. 2 Allow the projector at least 30 mins to cool down. 3 Disconnect the power cord. 4 Find the "OPEN" buttons on both sides of the projector and push it at the same time. (Illustration #1) 5 Open the top cover. (Illustration #2) 6 Remove the two screws that secure the lamp module.. and pull up the lamp bar...(Illustration #3) 7 Pull out the lamp module by force. (Illustration #4) To replace the lamp module, reverse the previous step. Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped. 1 2 4 3 1 2 40 English Ceiling Mount Installation If you wish to install the projector using a ceiling mount, please refer to the steps below: 1 Drill four holes into a solid, structurally sound part of the ceiling, and secure the mount base. Note: Screws are not included. Please obtain the appropriate screws for your type of ceiling. 2 Secure the ceiling rod using the appropriate type of four-cylinder screws. Ceiling Mount Base - Attach to ceiling Screw Type A 50 mm length / 8 mm diameter - Long Rod Extension Rod Long Cylinder Cap Allen Key - For tightening/looseni Tightening Screw Medium Rod Ceiling Mount Base Use the appropriate number of screws for the projector size to attach the projector to the ceiling mount bracket. Screw Type B Smaller Washer Large Washer Projector Bracket Supports projector and allows - for adjustments Spacer -For heat dissipation Note: It is recommended that you keep a reasonable space between the bracket and the projector to allow for proper heat distribution. Use two washers for extra support, if deemed necessary. Attach the ceiling bracket to the ceiling rod. Large cylinder cap Allen Key -For tightening/loosening Screw Type A 50 mm length - Tightening Screw ..8 mm diameter English EnglishEnglish 42 5 Adjust the angle and positioning as necessary. Tightening Screw Alle...
Dieses Handbuch ist für folgende Modelle:Projektoren - P1165P (4.71 mb)
Projektoren - P1265P (4.71 mb)