Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
060809-JA info@elitescreens.com Tripod Screen Parts Identification Tripod Screen Parts Identification Top Hook, Keystone Eliminator & Screen Handle Support beam Vertical Extension Bar Screen Material Screen case Carrying handle & Screen height adjustment lock/release tab Tripod junction Tripod Support Legs End cap Vertical locking sleeve ring Using the Screen A. Setting up the screen: Follow the steps below and Fig. 1 & 2. 1. Place the screen in an upright position (fig.1) with the legs toward the ground. 2. Deploy the Tripod Support legs by pushing down on the Tripod Junction. 3. Turn the tripod’s screen casing in a 90-degree horizontal position so that the screen casing is now parallel to the ground with the screen handle facing the bottom of the top hook. 4. Completely extend the legs as much as possible so they are stable and position them away from objects that may interfere with their balance. DO NOT stand the tripod on an unstable platform to avoid an injury should the tripod screen collapse. 1 3 2 4 Fig. 2 Fig.1 1 3 2 4 Fig. 2 Fig.1 1 B. Preparing the tripod screen for projection: Follow the steps below and Fig. 3. 1. Pull the screen handle up vertically and hook the screen handle on the Top Hook. *Note: Use the Keystone Eliminator to prevent “Keystone Effect” from occurring. Keystone Effect is caused when a projector presents its image at a downward angle causing a trapezoid-shaped image to appear on the screen. The Keystone Eliminator is designed to eliminate that effect by sloping the screen forward. 2. Twist the Vertical Locking Sleeve Ring counter-clockwise to unlock the current position of the Vertical Extension Bar and raise it as necessary to the desired height. 3. Pull the Screen Height Adjustment Lock/Release tab out (to the left) located just above the Carrying Handle to raise or lower the bottom of the. Once the desired height has been set, push the tab in to lock the position in place. 1 2 3 Fig. 3 2 C. Disassembling the screen: Follow the steps below and Fig. 4. 1. Unlock the Adjustment Handle by pulling the locking tab to the left and slowly slide the handle all the way down to bring down the position of the screen’s case. 2. Hold the Extension Bar and twist the Vertical Locking Sleeve Ring counter-clockwise to unlock and release the position of the extension bar. Once the extension bar has been brought all the way down, unhook the screen material from the Top Hook and slowly retract the screen back into the case. * Note: It is very important to remember to hold the extension bar first and then unlock the sleeve to prevent the extension bar from slamming and damaging the screen. 3. Turn the screen’s case vertically clockwise and insert the Top Hook’s bottom pin to lock into the screen’s end cap hole. 4. Close the tripod legs by pushing them in. Lastly, tighten the Vertical Locking Sleeve Ring by twisting it clockwise. 1 2 3 4 Fig. 4 Note: To ensure the screen is stable, extend the tripod’s legs as much as possible. Do not fold the screen or allow any sharp objects to touch the screen’s surface. Clean the screen surface often when needed. Careful use will extend the lifetime of this product. 3 Tripod Series Dimension Table Unit: inches Model Nominal Diagonal View Size H x W Screen Size H x W (A) Top of Screen at Highest Level (B1) Top of screen at lowest level (B2) Screen case at highest point (C1) Screen case at lowest point (C2) End cap size (D) Case length closed (D2) Case width closed (D3) T71NWS1 71"(1:1) 50"x50" 53"x53" 111.8 71.5 35.6 16.9 2.7 58.0 5.9 T71UWS1 71"(1:1) 50"x50" 53"x53" 111.8 71.5 35.6 16.9 2.7 58.0 5.9 T85NWS1 85"(1:1) 60"x60" 63"x63" 128.7 87.8 37.5 16.9 2.7 68.0 5.9 T85UWS1 85"(1:1) 60"x60" 63"x63" 128.7 87.8 37.5 16.9 2.7 68.0 5.9 T99NWS1 99"(1:1) 70"x70" 73"x73" 147.2 97.6 35.5 16.9 2.7 78.0 5.9 T99UWS1 99"(1:1) 70"x70" 73"x73" 147.2 97.6 35.5 16.9 2.7 78.0 5.9 T113NWS1 113"(1:1) 80"x80" 83"x83" 148.4 107.5 33.4 16.9 2.7 88.0 5.9 T113UWS1 113"(1:1) 80"x80" 83"x83" 148.4 107.5 33.4 16.9 2.7 88.0 5.9 T119NWS1 119"(1:1) 84"x84" 87"x 87" 148.4 111.8 37.1 16.9 2.7 91.9 5.9 T119UWS1 119"(1:1) 84"x84" 87"x 87" 148.4 111.8 37.1 16.9 2.7 91.9 5.9 T136NWS1 136"(1:1) 96"x96" 99"x99" 148.4 123.6 40.8 16.9 2.7 104.0 5.9 T136UWS1 136"(1:1) 96"x96" 99"x99" 148.4 123.6 40.8 16.9 2.7 104.0 5.9 T84UWV1 84"(4:3) 50"x67" 55"x70" 118.1 79.9 35.4 16.9 2.7 75.0 5.9 T100UWV1 100"(4:3) 60"x80" 65"x83" 139.4 89.8 53.4 16.9 2.7 88.0 5.9 T120NWV 120"(4:3) 72"x96" 77"x99" 148.4 102.0 65.0 16.9 2.7 104.0 5.9 T120UWV1 120"(4:3) 72"x96" 77"x99" 148.4 102.0 65.0 16.9 2.7 104.0 5.9 T92UWH 92"(16:9) 45"x80" 50"x83" 124.4 74.8 68.3 16.9 2.7 88.0 5.9 T100UWH 100"(16:9) 49"x87" 54"x90" 128.3 78.7 68.3 16.9 2.7 95.2 5.9 T120UWH 120"(16:9) 59”x105” 64"x108" 138.2 89.0 62.4 16.9 2.7 112.6 5.9 *Measurement dimensions are intended as a reference only and subject to change without notice Note:Data Error may be ±1" 4 Warranty Information • Two (2) year parts and labor warranty from ...