Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
Digital Light Processing is a trademark or registered trademark of Texas Instruments. InFocus, In Focus, and INFOCUS (stylized) are either registered trademarks or trademarks of InFocus Corporation in the United States and other countries. FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. EN 55022 Warning This is a Class A product. In a domestic environment it may cause radio interference, in which case the user may be required to take adequate measures. The typical use is in a conference room, meeting room or auditorium. Canada This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numerique de la classe A est conforme a la norme NMB-003 du Canada. Agency Approvals UL, CUL, TUV Other specific Country Approvals may apply, please see product certification label. This user’s guide applies to models IN32, C175, W320, IN34, C185, W340 InFocus reserves the right to alter product offerings and specifications at any time. Table of Contents Important Operating Considerations for Safety • Place the projector in a horizontal position no greater than 15 degrees off axis. • Locate the projector in a well-ventilated area without any obstructions to intake or exhaust vents. Do not place the projector on a tablecloth or other soft covering that may block the vents. • Locate the projector at least 4' (1.2 m) away from any heating or cooling vents. • Use only InFocus-approved ceiling mounts. • Use only the power cord provided. A surge-protected power strip is recommended. • Refer to this guide for proper startup and shutdown procedures. • This product has a lamp which contains a very small amount of mercury. Wash hands after cleaning the area and handling the ruptured lamp. Dispose of it as required by local, state or federal ordinances and regulations. For more information see org. • In the unlikely event of a lamp rupture, particles may exit through the projector side vents. When the projector is turned on, keep people, food, and drinks out of the "keep out" area under and around the projector, as indicated by the " X" areas below. 2’ / 0.6 m3’ / 1 m5’ /1.5m8’ /2.4m Follow these instructions to help ensure image quality and lamp life over the life of the projector. Failure to follow these may affect the warranty. For complete the warranty, see the Warranty booklet. Introduction Your new digital projector provides computer and video inputs and has XGA 1024x768 resolution. The projector is easy to connect, easy to use, and easy to maintain. Product specifications To read the latest specifications on your multimedia projector, be sure to visit our website at askproxima. com, as specifications are subject to change. Accessories The standard accessories that came with your projector are listed in the included user’s guide. Optional accessories can be found on our website at com or at your retailer or dealer. Online Registration Register your projector on our website at to activate your warranty and receive product updates, announcements, and registration incentives. keypadspeakerzoomfocus elevator foot releaseremotecontrolreceiver ( IR) Projector components and features connectorsleveling footheat ventIR receiverIR receiverstatus indicators Connector Panel The projector provides computer and video connectors: • one M1- D/A (HD, DVI, and computer) • one VESA (HD, HD component, and computer) • one VESA (monitor out) • one S- video • one composite RCA video • one audio in/one audio out It also has an RJ-45 connector for serial control. The Command Line Interface (CLI) specifications and commands are on our website. lockpowerconnectorM1-D/As- videocompositeexternalspeaker(audio out) RJ-45 serial controlvideocomputeraudio inVESA inmonitor out Connector panel Connecting a computer Required computer connections Connect the black end of the computer cable to the Computer 1 connector on the projector. Connect the blue end to the video port on your computer. If you are using a desktop computer, you first need to disconnect the monitor cable from the computer’s video port. Some Macintosh ® computers do not have a standard VESA-out video port. If the supplied computer cable will not connect to your computer, purchase the appropriate adapter from your Apple ® reseller. Connect the black power cable to the connector on the back of the projector and to you...