Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
• The operation range is limited. The shorter the distance between the Remote Commander and the projector is, the wider the angle within which the commander can control the projector. Installing the Projector This section describes the installation arrangements for installing the projector. Horizontal center of the screen Projection distance The distance between the lens and the screen varies depending on the screen size. Refer to the chart on page 28 (GB). Install the projector so that the tip of the lens is within this area. Installation area Vertical center of the screen Adjust the horizontal positioning of the projector so that the center of the lens is aligned with the horizontal center of the screen. Adjust the vertical and horizontal positioning of the projector. Vertical positioning (side view) Screen Adjustable shift range You can adjust the angle of projection by performing the shift adjustment (page 19 (GB)). Install the projector so that the center of the lens is between the bottom edge of the screen and the center of the screen. Horizontal positioning (top view) Screen Center of the projector 14 (GB) Connecting Connecting When making connections, be sure to: • turn off all equipment before making any connections. • use the proper cables for each connection. • insert the plugs of the cables properly; plugs that are not fully inserted often generate noise. When pulling out a cable, be sure to pull it out from the plug, not the cable itself. Connecting with a Computer or a VCR This section describes how to connect the projector to a computer or video equipment. Also refer to the instruction manual of equipment to be connected. Notes • This unit accepts the VGA, SVGA, XGA, SXGA or UXGA (60 Hz) signals. However, we recommend you to set the output signal of your computer to the XGA. • If you set your computer, such as a notebook type IBM PC/AT 1) compatible, to output the signal to both the display of your computer and the external monitor, the picture of the external monitor may not appear properly. In such cases, set the output mode of your computer to output the signal to only the external monitor. For details, refer to the operating instructions supplied with your computer. • This projector complies with DDC1 and DDC2B (Plug & Play). (DDC1 and DDC2B are the Display Data Channel (DDCTM) 2) standard in the VESA standard.) When connecting a DDC1 host system, the projector synchronizes with V.CLK that follows the VESA standard and outputs EDID (Extended Display Identification Data) to the data line. When connecting a DDC2B host system, the projector automatically switches to the appropriate communication mode. The INPUT B RGB (DVI) connector complies with the VESA DDC2B. If your computer or graphics board is compatible with DDC, turn on the power of the equipment as follows: 1 According to the input signal, set INPUT-B TERM. in the SET SETTING menu to PC ANALOG or PC DIGITAL. 2 Connect the projector to the computer with the DVI cable. 3 Turn on the power of the projector. 4 Boot up the computer. Setting up and projecting INPUT A R/R-Y/PR INPUT B RGB (DVI) INPUT C ETHER B/B-Y/PBG/Y SYNC/HD MONITOR OUT VIDEO IN VIDEO OUT S VIDEO VIDEO TRIG RS-232C PLUG IN POWER CONTROL S VD Computer to DVI output DVI cable (not supplied) VCR to S video output S-Video cable (not supplied) to video output Video cable (not supplied) Front of the projector SMF-400 Monitor cable (5BNC y HD D- sub 15pin) (not supplied) to monitor out SMF-410 Monitor cable (HD D-sub 15-pinyHD D-sub 15-pin) (not supplied) Monitor Computer to monitor input Notes • Set INPUT-A in the SET SETTING menu to COMPUTER when you connect the computer to the INPUT A connector. For details, see page 26 (GB). • When connecting a Macintosh3) computer equipped with video output connector of a type having two rows of pins to the INPUT A connector, use a commercially available plug adaptor. • Select PC DIGITAL or PC ANALOG using INPUTB TERM. in the SET SETTING menu depending on the signal input. For details, see page 26 (GB). ......................................................................................................................................................................................................... 1) IBM and PC/AT are a trademark and a registered trademark of International Business Machines Corporation, U.S.A. 2) DDCTM is a registered trademark of the Video Electronics Standard Association. 15 (GB) 3) Macintosh is a registered trademark of Apple Computer Inc. Connecting Connecting with a 15k RGB/ Component Equipment This section describes how to connect the projector with a 15k RGB/component equipment. Also refer to the instruction manuals of the equipment to be connected. INPUT A R/R-Y/PR INPUT B RGB (DVI) INPUT C ETHER B/B-Y/PBG/Y SYNC/HD MONITOR OUT VIDEO IN VIDEO OUT S VIDEO VIDEO TRIG RS-232C PLUG IN POWER CONTROL S VD Front of the projector to RGB/component output 15k RGB/component equipment Monitor cable (not supplied) Notes • ...