Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
Confirm that the screen shows “Manual Connection 3” for the connection profile. 3 3 On the Wireless Connection 2 window, select “Switch Connection Profile” on the “Connection” menu. • This will display a dialog box for switching the connection profile. 4 4 Click the [New] button. • This will display a dialog box for configuring a new manual connection profile. 5 5 On the dialog box for configuring the manual connection setup, configure the settings so they are the same as those that you configured for Manual Connection 3 in step 1 of this procedure. • Make sure that the IP address is different from the IP address you set in step 1, the IP address of the access point, and any other IP address within the same network. • For details about each of the settings on the dialog box, see “Manual Connection Setting Reference” (page 40). 31 6 6 After configuring all of the settings you want, click the [Register] button. 7 7 On the confirmation dialog box that appears, click the [OK] button. • This will register your settings as a new connection profile and return to the connection profile switching dialog box in step 1. 8 8 Click the [Connect] button. • This closes the connection profile switching dialog box and displays the dialog box shown below. • When the computer finds the Data Projector, the display will change to a dialog box like the one shown below for selecting the connected device. 9 9 Move the highlighting to “Projector A” for the projector name and then click the [OK] button. • This will establish a wireless LAN connection between the computer and Data Projector. • This will close the connected device selection dialog box and display the Wireless Connection 2 window on the computer screen. 10 10 On the Wireless Connection 2 window, click one of the projection area position buttons and then click the button. • This will cause the contents of the computer screen to be projected so they fill the entire projection area. • For details about Wireless Connection 2 window operations and Data Projector remote controller operations you can perform after establishing a connection, see “Using Wireless LAN for Projection” (page 50). 32 To modify an existing computer connection profile 1 1 Display the Wireless Connection 2 window by double-clicking the icon on your computer desktop, or select the following from the windows Start menu: [All Programs] - [CASIO] - [Wireless Connection 2]. • This step is not necessary if the Wireless Connection 2 window is already displayed. 2 2 On the Wireless Connection 2 window, select “Switch Connection Profile” on the “Connection” menu. • This will display a dialog box for switching the connection profile. 3 3 Click the “Profile Name” down arrow button and then select the connection profile you want to modify from the menu that appears. 4 4 Click the [Change Setup] button. • This will display a dialog box for configuring a new manual connection profile. 5 5 On the dialog box, modify the settings as required. • For details about each of the settings on the dialog box, see “Manual Connection Setting Reference” (page 40). 6 6 After configuring all of the settings you want, click the [Register] button. • This will cause the dialog box shown below to appear. 7 7 Click the [OK] button. • This registers the settings you modified in the manual setting in step 5 and returns to the connection profile switching dialog box. 8 8 Click the [Close] button. • This will return to the Wireless Connection 2 window. 33 Sending Settings from a Computer to the Data Projector You can use the Send Settings function of Wireless Connection 2 to send the settings to the Data Projector. To send connection profile settings from a computer to the Data Projector 1 1 Establish a wireless LAN connection between the computer and Data Projector. • For information about connection procedures, see “Using a Simple Connection Profile for a Wireless LAN Connection between the Data Projector and a Single Computer” (page 9). 2 2 On the Wireless Connection 2 window, select [Connection] -[Switch Connection Profile], which will display the Switch Connection Profile dialog box. 3 3 Click the “Profile Name” down arrow button and then select the manual connection profile you want to send from the menu that appears. • If you want to send Wireless Connection 2 initial manual connection profile values to the XJ-S35/YP-100, here you should select Manual Connection 1, Manual Connection 2, or Manual Connection 3. • You cannot select Simple Connection 1, Simple Connection 2, or Simple Connection 3. 4 4 Click the [Send Settings] button. • This will display the Send Settings dialog box. • If you want to send Wireless Connection 2 initial manual connection profile values to the XJ-S35/YP-100, use this dialog box to select the same connection profile that you selected in step 3, above. 5 5 Select a destination (Manual Connection 1, Manual Connection 2, or Manual Connection 3), and then click the [OK] button. • This will display a dialog box p...